Introduction
CP6003-SA
Page 1 - 4
ID 1044-9757, Rev. 2.0
P R E L I M I N A R Y
1.2
Board-Specific Information
The CP6003-SA is a CompactPCI single-board computer based on the 2
nd
generation Intel®
Core™ i7 and i5 processors and specifically designed for use in highly integrated platforms with
solid mechanical interfacing for a wide range of industrial environment applications.
Some of the CP6003-SA's outstanding features are:
•
Support for the following 2
nd
generation processors:
•
Quad-core Intel® Core™ i7-2715QE (SV), 2.1 GHz, 6 MB L3 cache
•
Dual-core Intel® Core™ i7-2655LE (LV), 2.2 GHz, 4 MB L3 cache
•
Dual-core Intel® Core™ i5-2515E (SV), 2.5 GHz, 3 MB L3 cache
•
Intel® QM67 Express chipset
•
Up to 16 GB, dual-channel, DDR3 SDRAM memory with ECC running at 1333 MHz on two
SODIMM sockets
•
Integrated 3D high-performance graphics controller with three high-resolution graphics in-
terfaces (VGA / 2 x HDMI/DVI)
•
64-bit/66 MHz PCI or PCI-X CompactPCI interface (PICMG 2.0)
•
One PMC slot with PCI functionality and with rear I/O support; 64-bit/66 MHz PCI inter-
face or 64-bit/133 MHz PCI-X interface
•
One XMC slot utilizing a x8 lane PCI Express 2.0 interconnection
•
Five Gigabit Ethernet interfaces:
•
Three Gigabit Ethernet interfaces on front I/O
•
Two Gigabit Ethernet interfaces on rear I/O (PICMG 2.16)
•
Two Gigabit Ethernet (GbE) controllers:
•
One Intel® 82579LM Gigabit Ethernet controller connected to one GbE port on the front panel
•
One Intel® 82580EB Quad Gigabit Ethernet controller connected to two GbE ports on
the front panel and two GbE ports on the rear I/O
•
Six Serial ATA interfaces with SATA RAID 0/1/5/10 support:
•
One onboard SATA 6 Gb/s interface for the standard SATA onboard connector
•
One onboard SATA 6 Gb/s interface for either one Serial ATA Flash module or one
Serial ATA 2.5" hard disk drive (HDD) / solid state drive (SSD)
•
Four SATA 3 Gb/s interfaces on the rear I/O
•
Six USB ports:
•
Two USB 2.0 ports on the front panel
•
Four USB 2.0 ports on the rear I/O
•
Two COM ports:
•
One RS-232 COM port either on the front panel or on the rear I/O (COMA)
•
One RS-422 COM port on the rear I/O (COMB)
•
TCG 1.2 compliant Trusted Platform Module (TPM), on request
•
Two SPI boot flashes to provide firmware redundancy:
•
One standard SPI boot flash
•
One recovery SPI boot flash
•
Watchdog timer
•
Battery-backed real-time clock (RTC)
•
Three onboard DIP switches for board configuration
•
Supports PICMG Packet Switching Backplane Specification 2.16
•
IPMI support
•
4HP, 6U CompactPCI
•
Passive heat sink solution for forced-airflow cooling
•
Rear I/O on J3 and J5; optionally on J4 for PMC/XMC only
•
Hot swap capability: as system controller or as peripheral device
•
AMI Aptio®, a uEFI-compliant platform firmware
