KONLEN TECHNOLOGY LIMITED
Website: www.konlen.com
U1 building, Oriental Garden, NanShan District, Shenzhen City, Guangdong Province,China
Tel: +86-(0)755-86082432 E-mail:
MSN:
Skype: securitykonlen
5
How to control the host
1.
Sending message to the host phone number (SIM Card number)
Send the message to the host: enter password 123456#, add the following command to set the host;
2.
Calling the host phone number (SIM Card number)
Call in the host and enter password 123456#, then input the following command to set the host:
Com
Function
Com
Function
1#1#
Outdoor arm* (all detectors work)
1#2#
Indoor arm (part detectors work)
1#0#
Disarm *(all detectors not work)
3#1#
Sounding immediately
3#0#
Stop sounding
4#1#
Open listen-in (use phone key )*
4#0#
Closed listen-in (use phone key )
11#1#
Need siren sound when alarming *
11#0#
No siren sound when alarming
12#1#
Sending SMS when alarming *
12#0#
No SMS when alarming
15#1#
Dial phone number when alarming *
15#0#
Just alarm and no dialing
16#1#
Disable Relay close 3 Min when alarming
16#0#*
Set Relay close 3 Min when alarm*
30##
show the arm and disarm status of every zone
31#--#
Change password. Enter a new password (1-6 bit).
38#--#
Set up alarm of zone (wireless zone: 1-16; wire zone: 21-23)
（
NOTE: arm of single defense zone
）
39#--#
Turn off alarm of zone (wireless zone: 1-16; wire zone: 21-23)
（
NOTE: disarm of single defense zone
）
50##
show preset phone number in the host
51#--#
First group phone number(0-15bit)
52#--#
Second group phone number(0-15bit)
53#--#
Third group phone number(0-15bit)
54#--#
fourth group phone number(0-15bit)
55#--#
Fifth group phone number(0-15bit)
80##
show preset SMS in the host
81#--#
First group Message(0-24bit)
82#--#
Second group Message(0-24bit)
83#--#
Third group Message(0-24bit)
84#--#
Fourth group Message(0-24bit)
85#--#
Fifth group Message(0-24bit)
86#--#
Sixth group Message(0-24bit)
87#--#
Seventh group Message(0-24bit)
90##
Show Output status in the host
91#1#
Set Output 1 change to high
91#0#
Set Output 1 change to low
92#1#
Set Output 2 change to high
92#0#
Set Output 2 change to low
93#1#
Set talk to the host available (Output 3)
93#0#
Set talk to the host unavailable (Output 3)
94#1#
Set Relay to be connected
94#0#
Set Relay to be disconnected
95#1#
Set alarm when line input 1 open
95#0#
Set alarm when line input 1 connect to Gnd*
96#1#
Set alarm when line input 2 open
96#0#
Set alarm when line input 2connect to Gnd*
97#1#
Set alarm when line input 3 open
97#0#
Set alarm when line input 3connect to Gnd*
Note:
1. Above table, ‘ * ’ stands for default setting.
2. In the above phone operation, one beep shows the number your input is successful, a long beep shows the sentence
you input is successful, two short beeps show sentence you input is failed, you should try again.