Kondo KXR-R4LL Assembly Manual Download Page 57

Page: 57 / 60

03115

02181

02182

03103

02141

02142

02183

03120

02146

02177

02166

02116

01228

01229

02336

03099

03106

03062

03124

03123

02125

02335

51204

02167

51203

02334

04045

04046

04047

04048

KRS-3301 ICS

Plastic gear set [KRS-3301]

Servo case [KRS-3301]

KRS-3304 ICS

Servo gear set [KRS-3304]

Servo case [KRS-3300 series]

Case screw set [KRS-3300 series] (20pcs)

RCB-4 mini

Connection Cable (1.5m)

ZH Conversion cable (100mm)

LV Power switch Harness

Dual USB Adapter HS

Sole grip A (High grip)

Sole grip B (Normal)

Grip sheet 70x30mm (Normal) (２ sheets)

KRC-5FH Tx / Rx set

KRR-5FH Rx

Bluetooth module KBT-1

KRG-4 B set (ZH⇔ZH) ２ sets

RAS-3 B set (ZH⇔ZH)

PSD sensor B set (ZH⇔ZH)

ROBO Power cell E type 6N-800 (Ni-MH)

USB charger BX-32MH (Ni-MH only)

ROBO Power cell F2-850 type (Li-Fe)

USB charger BX-31LF (Li-Fe only)

Decal (KXR)

Cushion grip driver 610 ＋ #0 x 100

Cushion grip driver 610 ＋ #1 x 100

Cushion grip driver 610 ＋ #0 x 75

Cushion grip driver 610 ＋ #1 x 75

Standard servo for KXR.

For KRS-3301.

Upgrade servo. Same size as 3301.

For KRS-3304.

For KRS-3300 series.

Standard control board for KXR.

Connect to Robot from PC.

Connect to RCB-4mini from Dual USB Adapter HS.

For LV Battery use.

For USB connection to PC.

For Sole. Soft type.

For Sole. Hard type.

Multiuse free cut. Hard type.

2.4Ghz wireless controller and reciever set.

Add on reciever.

Bluetooth connect to PC / Android device.

Gyro sensor for stability.

Accelerometer for judge lie down facing up or down.

Infrared distance sensor.

Nickel-metal hydride rechargeable battery.

For USB charging adapter (5V2A)

Lithium ferrite rechargeable battery.

For USB charging adapter (5V2A)

Standard decal.

Easy to turn with rubber grip. Magnet tip.

Open

¥ 300

¥ 600

Open

¥ 3,500

¥ 600

¥ 400

¥ 9,800

¥ 800

¥ 400

¥ 800

¥ 6,000

¥ 300

¥ 600

¥ 14,500

¥ 7,500

¥ 12,000

¥ 9,000

¥ 3,800

¥ 2,200

¥ 3,500

¥ 2,800

¥ 2,700

¥ 2,800

¥ 500

¥ 450

Wireless Unit

※The KRC-5FH wireless controller in only certiﬁed in Japan.

Servo Motor

Control Board、Cable

Sensor

Battery、Charger

Decal、Driver

Grip Sponge

KXR Option Parts List

Part No.

Part Name

Contents

Price

Please check KONDO web site for more information.

Option Parts List 2

Summary of Contents for KXR-R4LL





























































Search results

Summary of Contents for KXR-R4LL

Reviews:

Related manuals for KXR-R4LL

Brands by name

Popular brands

Kondo KXR-R4LL, Assembly Manual

Search results

Summary of Contents for KXR-R4LL

Reviews:

Related manuals for KXR-R4LL

Brands by name

Popular brands