Kondo KXR-R4LL Assembly Manual Download Page 36

Page: 36 / 60

Parts Combination 2

Backpack

SIO1

SIO2

SIO3

SIO5

COM

SIO6

SIO7

AD1

AD2

AD3

AD4

AD5

■

Cover lock

＊When inserting the connector, make sure

the direction is correct.

Power

Blue： COM port

Servo/receiver, etc.

Sensor, etc.

ZH Conversion cable （PC）

White: SIO port

Green: AD port

VH type-2PIN

ZH type-3PIN

ZH Conversion cable

Be careful of the protruding direction and do not

force it in.

Be sure to conﬁrm the lock/guide direction and

that it is not connected backward.

②Connect wire.

When operating the robot, lock the cover

with 2.6-4 screws so that it does not

unexpectedly open and shut.

2.6 ー 4

LV Power Source Switch Harness

LV Power Source Switch Harness

200mm

Right Rear

Wheel

Right Front

Wheel

Left Rear

Wheel

Left Front

Wheel

200mm

KXR-R4LL

Summary of Contents for KXR-R4LL





























































Search results

Summary of Contents for KXR-R4LL

Reviews:

Related manuals for KXR-R4LL

Brands by name

Popular brands

Kondo KXR-R4LL, Assembly Manual

Search results

Summary of Contents for KXR-R4LL

Reviews:

Related manuals for KXR-R4LL

Brands by name

Popular brands