14
2 PCB settings
I/O CHECK
•If the steering wheel or the accelerator is not properly adjusted, make the
necessary adjustments while referring to “7-5 Replacing and adjusting the
potentiometer” on pages 55 to 63 of the “RACING JAM
TM
” Operator’s Manual.
•The marker position changes to show the input
value.
•Shows the value for steering wheel in decimal
(hexadecimal).
The steering wheel is set properly when the steering
wheel is fully turned clockwise and the red “I” mark
comes to the “RIGHT” position as well as when the
wheel is fully turned counterclockwise and the mark
comes to the “LEFT” position.
•Shows the value for the accelerator pedal [decimal
(hexadecimal)]. if the "I" mark moves to “MIN”
when the accelerator pedal is eleased and to “MAX”
when the accelerator pedal is fully press, the
accelerator pedal is properly adjusted.
•Shows the value for the foot brake unit [decimal
(hexadecimal)].
Make sure the “I” make moves to “MIN” when
the foot brake is released and to “MAX”when the
foot brake is fully pressed.
•Shows the value for hand brake in decimal
(hexadecimal).
The hand brake is set properly when the hand brake
is released and the “I” mark comes to the “MIN”
position as well as when the hand brake is pulled up
and the mark comes to the “MAX” position.
•Shows the value for the clutch pedal [decimal
(hexadecimal)]. if the "I" mark moves to “MIN”
when the clutch pedal is eleased and to “MAX”
when the clutch pedal is fully pressed, the clutch pedal
is properly adjusted.
•Check the steering wheel reaction device by putting
down the shift lever while pressing the START button.
The steering wheel turns automatically
clockwise and counterclockwise by turns during
checking. Then, make sure that the “I” mark moves
accordingly to the right and left on the meter which
shows the value for the steering wheel. Do not touch
the steering wheel while this checking is conducted.
GEAR SHIFT LEVER
1 3 5 UP OFF DOWN OFF
ERROR LEFT OFF RIGHT OFF
2 4 R
STEERING WHEEL
0.0000
(
0000
)
ACCEL PEDAL
0.0000
(
0000
)
FOOT BRAKE PEDAL
0.0000
(
0000
)
HAND BRAKE LEVER
0.0000
(
0000
)
CLUTCH PEDAL
0.0000
(
0000
)
LEFT CENTER RIGHT
+---+--------------------------------------------------------+---+
MIN MAX
+---+--------------------------------------------------------+---+
MIN MAX
+---+--------------------------------------------------------+---+
MIN MAX
+---+--------------------------------------------------------+---+
MIN MAX
+---+--------------------------------------------------------+---+
HOLD START BUTTON AND GEAR SHIFT DOWN = ACTIVE STEERING TEST
HOLD GEAR SHIFT UP AND PRESS START BUTTON TO EXIT
I/O CHECK
START BUTTON OFF COIN MECH SWITCH OFF
SERVICE SWITCH OFF TEST SWITCH OFF
Checking the controls
2-4 Mode descriptions
The original factory settings are displayed in green; the changed settings are
displayed in red.
·To change the settings, move the shift lever up or down to select an item, and
press the START button to enter it.
·After the setting change, select “SAVE AND EXIT” and press the START button.
The settings are saved automatically and the screen returns to the main menu.
·If "EXIT" is selected after the modification of the settings, the following message
will appear:
"YOU DID NOT SAVE. DO YOU WANT TO SAVE? YES / NO" Select "YES" or
"NO" by shift lever up or down and set it by pressing the START button.
If "YES" is selected, the new settings will be saved with "NOW SAVING" displayed
and the screen will return to the main menu.
If "NO" is selected, the new settings will not be saved with "NO MODIFICATION"
displayed and the screen will return to the main menu.
•If "FACTORY SETTINGS" is selected and the START button is pressed, all the
settings of the mode will be back to the factory ones.
MEMO
Mode for checking the performance each control.
To return to the main menu screen, hold down the START button and move up the
shift lever.
MEMO
•This screen is just an example.
