background image

6

SPECIFICATIONS

European Conformity Information

The Mira Sport Thermostatic range of showers complies with the following European 

directives:

2006/95/EC Low Voltage Directive, 2004/108/EC EMC Directive.
The Mira Sport range of showers are high power appliances and are subject to conditional 

connection. If the main electrical supply fuse is rated less than 80 Amps, the local electricity 

supply company must be contacted to confirm if the electrical supply is adequate. 
The Mira Sport Thermostatic range of showers complies with the requirements of the UK’s 

water regulations.

Plumbing

Thermostatic Variant

Sport 9.0

Sport 9.8

Minimum Dynamic Pressure

70 kPa (0.7 bar)

Maximum Dynamic Pressure *

500 kPa (5 bar)

Minimum Static Pressure

20 kPa (0.2 bar)

Maximum Static Pressure *

1000 kPa (10 bar)

Maximum Inlet Temperature

30°C

Minimum Inlet Temperature

2°C

Inlet Connection

1/2" BSP Male / 15 mm Compression Fitting

Maximum Water Hardness

200 ppm CaCO

3

Outlet Connection

1/2" BSP Male

Electrical

Thermostatic Variant

Sport 9.0

Sport 9.8

Nominal Power at 230 V ac

8.3 kW

9.0 kW

Nominal Power at 240 V ac

9.0 kW

9.8 kW

Recommended MCB Rating

40 A

45 A

Maximum Supply Cable Size 

16 mm²

Recommended RCD Rating

30 mA tripping current

Recommended Isolator Switch

45 A double-pole with 3 mm contact separation

Appliance Sealing Rating

IP X4 - Suitable for installation in Zone 1

Maximum Ambient Temperature

30°C

Minimum Ambient Temperature

2°C

Dimensions

Height

358 mm

Width

215 mm

Depth

90 mm

*A drop tight pressure reducing valve should be installed where dynamic or static pressure 

exceeds the figure stated in the Specifications.

Summary of Contents for Mira Sport Thermostatic






















Reviews: