background image

3

IMPORTANT SAFETY INFORMATION

WARNING - This shower can deliver scalding temperatures if not operated, 
installed or maintained in accordance with the instructions, warnings and 
cautions contained in this guide and on or inside the appliance. 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1.  Installation of this shower must be carried out in accordance with these 

instructions by qualified, competent personnel. 

2. 

Isolate the electrical and water supplies before commencing installation. The 

electricity must be isolated at the consumer unit and the appropriate circuit 

fuse removed, if applicable. Mains connections are exposed when the cover 

is removed.

3. 

DO NOT

 install the shower in areas with high humidity and temperature  

(i.e. Steam rooms and saunas).

4. 

DO NOT

 install the shower where it may be exposed to freezing conditions. 

Ensure that any pipework that could become frozen is properly insulated.

5. 

DO NOT 

switch the shower on if there is a possibility that the water in the 

shower is frozen. 

6. 

DO NOT

 switch the shower on if water starts leaking from the shower case. 

Isolate the electrical supply to the shower immediately.

7. 

DO NOT

 connect the outlet of the shower to any tap, control valve, trigger 

handset or showerhead other than those specified for use with this shower. 

Only Kohler Mira recommended accessories should be used.

8.  The water supplies to this product must be isolated if the product is not to be 

used for a long period of time. If the product or pipework is at risk of freezing 

during this period they should also be drained of water.

9. 

DO NOT

 perform any unspecified modifications to the shower or its 

accessories. When servicing only use genuine Kohler Mira replacement 

parts.

10. 

If the shower is dismantled during installation or servicing then upon completion 

the product must be inspected to ensure all electrical connections are tight and 

that there are no leaks.

11. 

Read all installation instructions before installing this shower.

12. 

Upon completion of the installation, make sure that the user is familiar with the 

operation of the shower, and leave this guide and the user guide with the owner.

Summary of Contents for Mira Sport Thermostatic






















Reviews: