Kohler Mira Decor Page 20 Installation And User Manual Download | Manualshive

Page: 20 / 40

background image

20

1365393-W2-A

Install the slide bar assembly onto

the mounting brackets. Tighten the

2 x M4 screws with the supplied 3 mm

hexagonal key.

Install the end cap at top and the soap

dish at bottom.

Fit a hose seal into the conical nut and

screw onto the outlet of the shower.

Caution!

DO NOT

over tighten.

Feed the hose through the soap dish.

Fit a hose seal into the conical nut and

screw onto the showerhead.

Caution!

DO NOT

over tighten.

Place the showerhead assembly into the

clamp bracket.

Caution! DO NOT force assembly on

to the mounting brackets, re-align a

slide bar support if required.

«
...
18
19
20
21
22
...
»

Summary of Contents for Mira Decor









































Reviews:

No comments

Related manuals for Mira Decor

PuraVida 15770 Series

Brand: Hans Grohe Pages: 76

Brand: Oceanstar Pages: 3

Brand: Grohe Pages: 112

CARIMALI RIGOLETTO 21510-CR

Brand: Calflex Pages: 12

AQUAECO AQM-CND-301-XX

Brand: Sanipex Pages: 8

Brand: Helvex Pages: 2

Brand: Hans Grohe Pages: 579

Brand: Pfister Pages: 7

Brand: Toto Pages: 4

Washlet EK TCF6402G

Brand: Toto Pages: 40

Brand: Toto Pages: 48

Brand: Toto Pages: 24

Brand: Toto Pages: 24

Raindance E 150 1-Jet 04343 0 Series

Brand: Hans Grohe Pages: 12

Raindance 27145000

Brand: Hans Grohe Pages: 40

Raindance 260 x 260 mm Air 1jet 26472 Series

Brand: Hans Grohe Pages: 48

Raindance E 120 3-Jet Series

Brand: Hans Grohe Pages: 20

PuraVida 27844000

Brand: Hans Grohe Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands