manualshive.com logo in svg

Kohler Mira Decor, Installation And User Manual

Share
Download
Kohler Mira Decor Installation And User Manual Download Page 24

24

1365393-W2-A

Note: A spare grubscrew is supplied 

if damaged during installation.

Note: Do not hang products from the 

diverter link hose.

 

 

Decor

Angle the riser arm to the centre of the 

showering area and secure in place using 

the grubscrew.

Rotate the middle port of diverter to suit 

position of the shower unit.

Connect the diverter link hose to the 

diverter and the shower unit. Connect the 

red conical end with coarse thread to the 

shower outlet and the clear conical end 

with a fine thread to diverter inlet. If the 

diverter link hose is not long enough for 

your installation, please contact Mira to 

receive a longer hose.

Feed the long shower hose through 

the hose retaining ring and connect to 

the diverter outlet and the showerhead. 

Connect the conical with red cover or white 

label to the showerhead.

Place the showerhead assembly into the 

clamp bracket.

Red 

Conical

Clear 

Conical

Summary of Contents for Mira Decor









































Reviews:

No comments

Brands by name

Popular brands

Load more brands