Kohler 1190330-NA Installation And User Manual Download Page 10 | Manualshive

Page: 10 / 24

background image

10

1095640-W2-B

Reversing the Outlet Position

1.

Remove the outlet adapter using a 12 mm hexagonal wrench (not supplied).

2.

Remove the outlet blanking plug using a 12 mm hexagonal wrench.

3.

Screw the outlet adapter, complete with ‘O’ seal into the bottom hole previously

blanked and tighten.

4.

Screw the outlet blanking plug, complete with ‘O’ seal, into the top hole and

tighten.

Outlet Blanking

Plug

Outlet Adapter

Temperature Only valve shown

«
...
8
9
10
11
12
...
»

Summary of Contents for 1190330-NA

























Reviews:

No comments

Related manuals for 1190330-NA

Brand: ABB Pages: 63

Brand: Balboa Pages: 12

Brand: Paoli Pages: 16

Brand: VADDIO Pages: 2

Brand: Access Pages: 12

Brand: Wavelink Pages: 69

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: RadioMaster Pages: 49

SUPERREMOTE UR19A

Brand: X10 Pages: 3

Brand: Xantech Pages: 102

Brand: Xantech Pages: 17

Brand: X10 Pages: 2

Brand: Xylem Pages: 48

Brand: Vizio Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands