manualshive.com logo in svg

kobi NET-KOBI-IP-16CH, User Manual

Share
Download
kobi NET-KOBI-IP-16CH User Manual Download Page 143

 

 

143 

10.5

 

Checking HDD Status 

Purpose: 

You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case 
of HDD failure.

 

Checking HDD Status in HDD Information Interface   

Steps: 

1.

 

Enter the HDD Information interface. 

Menu > HDD>General 

2.

 

Check the status of each HDD which is displayed on the list, as shown in Figure 10. 18. 

 

Figure 10. 18

 

View HDD Status (1)

 

 

Note: 

If the status of HDD is 

Normal 

or 

Sleeping

, it works normally. If the status is 

Uninitialized 

or 

Abnormal

, 

please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one.   

Checking HDD Status in HDD Information Interface 

Steps: 

1.

 

Enter the System Information interface. 

Menu >Maintenance > System Info   

2.

 

Click the 

HDD

 tab to view the status of each HDD displayed on the list, as shown in Figure 10. 19. 

Summary of Contents for NET-KOBI-IP-16CH






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands