manualshive.com logo in svg

kobi NET-KOBI-IP-16CH, User Manual

Share
Download
kobi NET-KOBI-IP-16CH User Manual Download Page 116

 

 

116 

9.1

 

Configuring General Settings 

Purpose: 

Network settings must be properly configured before you operate NVR over network. 

Steps: 

1.

 

Enter the Network Settings interface. 
Menu >Configuration>Network 

2.

 

Select the 

General 

tab. 

 

Figure 9. 1

 

Network Settings Interface 

 

3.

 

In the 

General Settings 

interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 

Gateway, MTU and DNS Server. 
If the DHCP server is available, you can click the checkbox of 

DHCP

 to automatically obtain an IP 

address and other network settings from that server. 

Note:

 

The valid value range of MTU is 500 ~ 9676. 

4.

 

After having configured the general settings, click 

Apply

 to save the settings. 

 

Summary of Contents for NET-KOBI-IP-16CH






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands