Knight Multi-Flow Installation & Programming Instruction Manual Download Page 2

Page: 2 / 20

Page 2 of 20

0900455 Rev: F (06/02)

TABLE OF CONTENTS

Menu Map............................................................................................................. 3

Introduction........................................................................................................... 4

System Overview.................................................................................................. 4

Operation.............................................................................................................. 5

Pre-Installation ..................................................................................................... 6

Installation ............................................................................................................ 6

Keypad Diagram................................................................................................... 7

Display Window.................................................................................................... 8

Access Codes ...................................................................................................... 8

Dispenser Setup Menu ......................................................................................... 9

Calibrate Pumps Menu ....................................................................................... 14

Formula Settings Menu ...................................................................................... 15

User Menu .......................................................................................................... 16

Data Transfer Menu............................................................................................ 17

System Wiring Diagram ..................................................................................... 18

Warranty Information.......................................................................................... 20

Knight Locations................................................................................................. 20

CAUTION: The Multi-Flow laundry system has high voltage connected to the pump circuit board. Always
disconnect main power when servicing the unit.

Summary of Contents for Multi-Flow





















Search results

Summary of Contents for Multi-Flow

Reviews:

Related manuals for Multi-Flow

Brands by name

Popular brands

Knight Multi-Flow, Installation & Programming Instruction Manual

Search results

Summary of Contents for Multi-Flow

Reviews:

Related manuals for Multi-Flow

Brands by name

Popular brands