Knick Portavo 904 User Manual Download Page 19 | Manualshive

Page: 19 / 54

background image

19

Measurement

cal

CAL
INST. FACTOR

In narrow installation conditions, the conductivity
measurement is influenced by the sensor’s distance
to the wall and the wall material. This effect can be
compensated for by the installation factor. The meter
corrects the cell constant by multiplying it with the
installation factor. The value of the installation factor
depends on the diameter and the conductivity of the
pipe as well as on the sensor’s distance from the wall.
If the distance from the wall is sufficient (> 15 mm
(0.59"), DN 80 or larger), it is not necessary to consid-
er the installation factor (1.00). If the distance from
the wall is smaller, the installation factor increases
(> 1) when the pipe is electrically insulating and de-
creases (< 1) when the pipe is electrically conductive.
See the instructions in the sensor manufacturer’s
documentation.

cal

Value blinks

Use



to set the installation factor.

cal

Calibration is performed.
Display: CELL CONSTANT, INST. FACTOR.
The meter then automatically returns to measuring mode.

INST. FACTOR Calibration

(For inductive conductivity measurement only or with Memosens
4-electrode sensor with specification of installation factor)

Selected in the configuration menu.

Calibration

Calibration

Note:

To abort calibration, you can press

meas

at any time.

«
...
17
18
19
20
21
...
»

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

Brand: Icare Pages: 3

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hammond Pages: 16

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Wavetronix Pages: 14

Brand: LEM Pages: 33

Brand: Gates Pages: 112

Brand: Sur-Gard Pages: 12

Brand: RS PRO Pages: 41

Brand: Kawai Pages: 110

Brand: Vega Pages: 52

Brand: ABQ Industrial Pages: 32

Brand: National Instruments Pages: 24

Brand: M-Audio Pages: 21

MarMonix MSL-765

Brand: Farnell Pages: 15

Brand: Shimadzu Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands