Knick Portavo 904 User Manual Download Page 13 | Manualshive

Page: 13 / 54

background image

13

Commissioning

Commissioning

WARNING! Impairment of explosion protection.

When using the Portavo 904X (device variant for applications in hazardous loca-
tions) in a hazardous location, only the battery types listed below may be used.
The batteries must be from the same manufacturer and of identical type and
capacity. Never use new and used batteries together (see also Control Drawing
209.009-110).

Batteries for Application in Hazardous Locations

Batteries (4x each)

Temp. class

Ambient temperature range

Duracell MN1500

1)

T4

-10 °C ≤ Ta ≤ +40 °C

Energizer E91

T3

-10 °C ≤ Ta ≤ +50 °C

Power One 4106

T3

-10 °C ≤ Ta ≤ +50 °C

Panasonic Pro Power LR6

T3

-10 °C ≤ Ta ≤ +50 °C

A battery icon in the display indicates the battery power level:

Icon fully filled

Batteries at full capacity

Icon partially filled

Battery capacity is sufficient

Icon empty

Battery capacity not sufficient;
calibration is possible, no logging

Icon blinks

Max. 10 operating hours remaining, measure-
ment is still possible

NOTICE!

It is absolutely necessary to replace

the batteries.

1) The Duracell Plus Power 4ct (EAN: 5000394017641) is an MN1500 battery.

«
...
11
12
13
14
15
...
»

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

Brand: OfiTE Pages: 24

Brand: horiba Pages: 27

SoundTrack LxT N/Forcer

Brand: Larson Davis Pages: 12

Brand: Mark-10 Pages: 26

Brand: Autometers Systems Pages: 16

Brand: WATERGUARD Pages: 2

Brand: HBM Pages: 84

Brand: EPE Conseil Pages: 3

Brand: Primes Pages: 48

Brand: Hanna Instruments Pages: 28

Brand: Omega Pages: 4

Brand: LORECa Hearing Instrument Pages: 43

QI-POWER-485-300-LV

Brand: QEED Pages: 2

Brand: L.R. Baggs Pages: 6

Brand: Princeton Instruments Pages: 28

Brand: VOLTCRAFT Pages: 8

Brand: Trotec Pages: 3

BioTector B3500C

Brand: Hach Pages: 165

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands