Knick Portavo 904 User Manual Download Page 14 | Manualshive

Page: 14 / 54

background image

WARNING! Impairment of explosion protection.

Never use digital Memosens sensors without Ex approval in a hazardous location. For
these applications, you must use Memosens sensors with Ex approval. These sensors,
as well as the hazardous-area cables, are marked by an orange-red ring.

14

Connecting a Sensor

The Portavo 904(X) COND provides several connections so that many types of sen-
sors can be used for measurement (see illustration below).
Note that only

one

sensor may be connected to the meter at a time.

The meter automatically recognizes a connected Memosens sensor and switches
accordingly. Memosens is signaled in the display.

Separate Temperature Probe
Note:

Temperature measurement using a separate temperature probe is only possi-

ble when no Memosens sensor is connected.
After power-on, a separate temperature probe is automatically recognized. If you
want to replace the temperature probe, you must switch off the meter and then
switch it on again.

a

b

c

d

e

Connections

a - Micro USB port

b - M8, 4 pins for Memosens sensors

c - Temperature probe GND

d - Temperature probe

e - DIN socket, 8 pins for analog sensors

Commissioning

Memosens sensors have a cable coupling, which allows convenient replacement of
sensors while the cable remains connected to the meter. The connecting cable is
connected to socket

b

(M8, 4 pins for Memosens sensors).

«
...
12
13
14
15
16
...
»

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

Brand: X-Rite Pages: 80

Brand: C-LOGIC Pages: 2

Brand: Kane Pages: 4

Brand: DAKOTA ULTRASONICS Pages: 48

Brand: TE Connectivity Pages: 9

Brand: Ulvac Pages: 18

Brand: Datakom Pages: 2

Brand: Hanna Instruments Pages: 2

American AL-1000

Brand: Badger Meter Pages: 16

Brand: PCE Instruments Pages: 6

MultiScanner HD800 OneStep

Brand: Zircon Pages: 2

Brand: HERON Pages: 2

Brand: Ratek Pages: 24

Brand: Amptec Research Pages: 19

Brand: Magnetrol Pages: 48

Brand: GasQuip Pages: 8

Brand: Omni Instruments Pages: 8

Brand: Schaller Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands