Knick Portavo 904 User Manual Download Page 18 | Manualshive

Page: 18 / 54

background image

18

Calibration

0.1 / 0.01 MOL KCL Calibration

(Automatic calibration with KCl solution)

The calibration method is selected in the configuration menu.

Measurement

cal

CAL
0.1/0.01 MOL KCL
PRESS CAL

Dip sensor in KCl solution.
The meter automatically compensates for the
temperature deviation!

cal

Measured value
Temperature
Conductivity KCl
Hourglass blinks

Calibration is performed.

Display: CELL CONSTANT.
The meter then automatically returns to measuring mode.

Calibration

Important notes:

• Make sure that the values of the calibration solutions used correspond exactly

to those specified in this manual.
If not, the resulting cell constant will be incorrect.

• When calibrating in a liquid, make sure that the conductivity sensor, any sepa-

rate temperature probe, and the calibration solution have the same tempera-
ture. Only this ensures that the cell constant is determined correctly.

Note:

To abort calibration, you can press

meas

at any time.

«
...
16
17
18
19
20
...
»

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Brand: Oldham Pages: 34

Vario 4 Typ 4.5.1

Brand: techem Pages: 142

Brand: Jaquet Pages: 27

Micropilot S FMR533

Brand: E+H Pages: 12

Brand: National Instruments Pages: 169

Celviano AP-60R

Brand: Casio Pages: 44

Brand: Hanna Instruments Pages: 2

Victoreen 07-494

Brand: Fluke Biomedical Pages: 34

Brand: JPT Pages: 19

AcquiSuite Ally

Brand: Obvius Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands