Knick Portavo 904 OXY User Manual Download Page 19 | Manualshive

Page: 19 / 50

background image

19

Calibration

Measurement

cal

CAL
TEMP. OFFSET

You can specify an offset for the temperature

measured by the sensor.

After calibration has been activated, the follow-

ing values are listed in the display:

• temperature setpoint

• temperature measured by sensor

• offset (display in K)

cal

Temperature setpoint value
blinks.

Use



to set the temperature setpoint value.

cal

Calibration is performed, the offset value is indicated.
The meter then automatically returns to measuring mode.

TEMP. OFFSET OFFSET (option)

Temperature calibration (offset)
Selected in the configuration menu.

Calibration

Note: To abort calibration, you can press meas at any time.

«
...
17
18
19
20
21
...
»

Summary of Contents for Portavo 904 OXY



















































Reviews:

No comments

Related manuals for Portavo 904 OXY

Endura AZ20 series

Brand: ABB Pages: 8

Brand: OfiTE Pages: 24

Brand: Yamaha Pages: 8

Brand: Landis+Gyr Pages: 54

Brand: HANYOUNGNUX Pages: 4

Brand: Landis+Gyr Pages: 26

Brand: Landis+Gyr Pages: 3

Brand: LATNEX Pages: 55

Brand: Laser Technology Pages: 11

Brand: Laser Technology Pages: 62

Brand: YOKOGAWA Pages: 53

Brand: Major tech Pages: 16

Brand: Zoetis Pages: 2

Brand: RIDGID Pages: 18

DT4120 PS Series

Brand: Datcon Pages: 92

Cobra SMARTsense Ammonium Ion 12913-00

Brand: PHYWE Pages: 5

Brand: Agilent Technologies Pages: 198

Brand: MRC Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands