background image

3

MEMMERT GmbH + Co. KG

Willi-Memmert-Straße 90-96

D-91186 Büchenbach

Germany

Phone:    +49 (0)9122 925-0

Fax:  

  +49 (0)9122 14585

Email:     [email protected]

Internet:   www.memmert.com

Customer service:

Hotline: 

+49 (0)9171 9792 911

Service fax:  +49 (0)9171 9792 979 

E-mail: [email protected]

© 2018 Memmert GmbH + Co. KG

Safety regulations

After removing covers, live parts may be exposed. Touching these can lead to an 
electric shock. Disconnect the mains plug before removing any covers. Work on 
the electrical system must only be performed by quali

fi

 ed electricians.

Toxic gases or vapours may be produced in certain applications. These 
can escape from the vacuum pump into the room. This can injure people 
nearby. The appliance may only be used for such applications if a  suction 
is attached to the vacuum pump used, which reliably keeps toxic gases or 
vapours away from people. Observe the respective national regu-lations for 
occupational safety and environmental protection.

NOTICE

The operating manual of the MEMMERT vacuum oven contains important 
information and instructions how to use the pump module. Followall pos-
sible information from the related operating manual of the vacuum oven 
exactly.

WARNING

WARNING

Summary of Contents for PJ25481-950.50.18










































Reviews: