manualshive.com logo in svg

KNECHT W 200 II, Operating Instructions Manual

Share
Download
KNECHT W 200 II Operating Instructions Manual Download Page 34

35

8.  Care and maintenance 

8.1  Coolant additive

It is imperative to add a rust-suppressing coolant additive to the coolant (see Chapter 8.1.1).

ATTENTION

No other coolant additives may be used 
without the approval of KNECHT Maschinen-
bau GmbH.

8.1.1  Cooling lubricant maintenance plan

• Check fill level daily.
 •  After topping up with water, always measure the concentration and if necessary top up with 

cooling lubricant. 

• Check cooling lubricant concentration weekly.

Cooling lubricant:
Colometa SBF-PN

Refractometer  °Brix:  3 - 5

Date:

°BRIX

Conc %

Remarks
etc.

Signature

(The value read off in °Brix multiplied by 1.8 is the concentration in %).

The concentration must always be between 3 - 5 °Brix (corresponds to a concentration of 5 - 9%).

Check the odor and appearance of the cooling lubricant regularly. The cooling lubricant must 
be replaced at least every three months (biological hazard due to germ formation in the cooling 
lubricant).

Summary of Contents for W 200 II









































Reviews:

No comments

Brands by name

Popular brands

Load more brands