KMC Controls KMD-5210 Installation And Operation Manual Download Page 22 | Manualshive

Page: 22 / 38

background image

KMC Controls

Revision E

Installation

Connecting Power

22

Caution

D

o not

crimp the cable in a tight fold. This may result in separation of cable

strands and result in unreliable operation of the module.

4. Connect input and output devices to the modules. Refer to the manuals

supplied with the KMD-5220 input module and the KMD-5220 output
module for details.

Connecting Power

Each KMD-5210 LAN Controller requires a KMD–5563 power supply for
operating power. Mount the power supply in a convenient location near the
KMD-5210 and route the supply cable to the controller.

The controller will automatically power on when the power connection is
complete. The controller does not use an power switch. See

Applying power

for additional information.

Caution

Use only a KMC Controls power supply. Powering the controller with an
improper supply may result in damage to the controller.

«
...
20
21
22
23
24
...
»

Summary of Contents for KMD-5210







































Reviews:

No comments

Related manuals for KMD-5210

Brand: Valve Concepts Pages: 16

Brand: Quickmill Pages: 3

Brand: YASKAWA Pages: 256

Brand: Yardney Pages: 8

Brand: Bang & Olufsen Pages: 80

Brand: Bang & Olufsen Pages: 13

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Grafica DNE-K07

Brand: Paradox Pages: 24

Brand: Panosol Pages: 105

Brand: Pangolin Pages: 8

Brand: TCS Pages: 16

disklavier DKC-850

Brand: Yamaha Pages: 2

Real Living iM1

Brand: Yale Pages: 2

Brand: Atmel Pages: 12

Brand: Ublox Pages: 58

Brand: Mircom Pages: 20

Brand: Swagelok Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands