KMC Controls KMD-5210 Installation And Operation Manual Download Page 20 | Manualshive

Page: 20 / 38

background image

KMC Controls

Revision E

Installation

Planning for input and output modules

20

Planning for input
and output
modules

To connect inputs or output devices to a KMD-5210 controller, use KMD-5220
input and KMD-5221 output modules. The KMD-5210 controller includes
eight universal I/O ports for up to eight KMD-5220 input modules, eight
KMD-5221 output modules or any combination of up to eight modules.

Each module connects to the controller using a flat ribbon cable. When
connecting input and output modules, use the following guidelines.

◆

Connect the first KMD-5220 input module to connector

I/O Card 1

; add

continue adding input modules from left to right

◆

Connect the first KMD-5221 output module to connector

I/O Card 8

and

continue adding output modules from right to left.

◆

Use ribbon cables no longer than 24 inches (61 cm).

◆

KMD-5221 output modules require an output transformers.

Illustration 2-8 Typical input and output module connection

«
...
18
19
20
21
22
...
»

Summary of Contents for KMD-5210







































Reviews:

No comments

Related manuals for KMD-5210

Brand: Particle Pages: 6

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: HANYOUNG NUX Pages: 56

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: Savant Pages: 2

JetWeb JX2-PRN1

Brand: Jetter Pages: 25

TBEN-L 8IOL Series

Brand: turck Pages: 148

APEXpy 07-37A2-2111/ 520Series

Brand: Bartec Pages: 98

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Velux Pages: 11

Brand: Kantronics Pages: 201

CITY MICRO DOUBLE

Brand: Baby Jogger Pages: 9

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands