KMC Controls 68 Series Operator'S Manual Download Page 52 | Manualshive

Page: 52 / 80

background image

50

Bedder Door Shaper:

The Bedder Door Shaper (02-027-173) is bolted to the bot-
tom of the Bedder Door Assembly using 3/8 x 1 1/2 Car-
riage Bolts, lockwasher, and hexnuts.

Door Shaper

(02-027-173)

36” Row

Double Bedder Door Setups:

All double bed doors can be set up to the following row patterns using (30-40) DB Door Assembly (06-082-164) except for
the 48” Row Pattern that uses the (48) DB Door Assembly (06-082-184) & 46” Row Pattern that uses the (46) DB Door
Assembly (06-082-190).

32” Row

Cut off excess

shoe for mount

beside next door

34” Row

End slot in shoe

thru this bolt.

Cut off excess

shoe for mount

beside next door

30” Row

Cut off excess

shoe for mount

beside next door

End slot in shoe

thru this bolt.

End slot in shoe

thru this bolt.

End slot in shoe

thru this bolt.

30”

(TYP)

34”

(TYP)

32”

(TYP)

36”

(TYP)

«
...
50
51
52
53
54
...
»

Summary of Contents for 68 Series

















































































Reviews:

No comments

Related manuals for 68 Series

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: R.M. Young Pages: 10

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: Waters Pages: 250

Brand: Waters Pages: 141

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 3

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 36

Brand: YASKAWA Pages: 1166

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands