KMC Controls 68 Series Operator'S Manual Download Page 78 | Manualshive

Page: 78 / 80

background image

76

STORAGE:

The purchase of your Ripper Bedder is a substantial investment to your farming needs. For this

reason, your Ripper Bedder should be cleaned and stored in a manner that will ensure the life and
value of your investment for years to come.

KMC recommends after each season of use to:

•

Pressure wash and clean the machine thoroughly to remove all dirt and moisture
retaining materials.

•

Repaint worn and scratched parts if possible.

•

Grease all bearings, bushings, and pivot joints that are fitted for relube. Also, fully
grease the turnbuckle threads to prevent these areas from rusting and pitting.

•

Store under a shelter in a location away from all weather elements if possible.

TIRE INFLATION CHART

It is important that the inflation of all tires be set properly for maximum safety and per-
formance. Use the following guide to adjust the inflation pressure in the tires to match
the application of the machine.

COLD INFLATION PRESSURE VALUES IN PSI

TIRE SIZE

COLD INFLATION PRESSURE

7.60 X 15SL (8-PLY)

(Toolbar Gauge Wheels)

52 psi

(Cold)

20.5 X 8.00-10 (4 PLY)

(8 X 10 Press Wheels)

35 psi

(Cold)

«
...
76
77
78
79
80
»

Summary of Contents for 68 Series

















































































Reviews:

No comments

Related manuals for 68 Series

Brand: Nemco Pages: 13

Brand: Ecco Pages: 12

Brand: UMF Medical Pages: 12

Brand: Landoll Pages: 83

Brand: Raymarine Pages: 90

Brand: IBS Scherer Pages: 64

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Gardigo Pages: 32

Brand: Patiova Pages: 19

Synthesis SDEC-3000

Brand: JBL Pages: 24

Brand: Xilica Audio Design Pages: 30

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

Brand: VanGaa Lighting Pages: 7

GPSMAP 7400 Series

Brand: Garmin Pages: 8

Brand: Bayer HealthCare Pages: 104

EDC2-1001-RGB-MWT

Brand: Energizer Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands