KMC Controls 68 Series Operator'S Manual Download Page 48 | Manualshive

Page: 48 / 80

background image

46

RIPPER TOOL OPTIONS:

A TRIPPED SHANK IS UNDER EXTREME
FORCE. STAY CLEAR OF A TRIPPED
SHANK! FAILURE TO COMPLY WILL
RESULT IN SERIOUS INJURY OR DEATH.

DANGER

The 6800 Series Ripper Bedder comes equipped with a choice of the Reset on the Go Ripper Shank or
the Toggle Trip Shank. Either of these will be pre-mounted to the bar when the unit arrives. Verify the
pre-mount location of all the shanks by using the “

Overhead Layout

” portion of this section. It may be

necessary to mount some of the wear items associated with these ripper shanks using the following:

For the KMC Ripper Points use (1) 3/8 x 1 1/4” long roll pins to secure in place on each shank as

shown. For KMC Shank Wear Shins use (3) 5/16 x 1 3/8” long roll pins to secure to each shank as
shown. Once all items on each shank are in place verify that all hardware is in place and properly
tightened and secured.

Toggle Trip Shanks

SHANK WEAR SHIN

5/16 X 1 3/8 ROLL PINS

3/8 X 1 1/4 ROLL PIN

RIPPER POINTS

Reset-On-The-Go Shanks

SHANK WEAR SHIN

5/16 X 1 3/8 ROLL PINS

3/8 X 1 1/4 ROLL PIN

RIPPER POINTS

«
...
46
47
48
49
50
...
»

Summary of Contents for 68 Series

















































































Reviews:

No comments

Related manuals for 68 Series

Brand: Balanced Body Pages: 4

Brand: FENDT Pages: 31

Brand: DBX Bushido Pages: 12

Brand: Eaton Pages: 21

Brand: NANO Pages: 4

Brand: Pablo Pages: 7

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: Össur Pages: 82

Brand: GE Pages: 2

Brand: Woods Pages: 54

Brand: AMVAC Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands