KMC Controls 68 Series Operator'S Manual Download Page 50 | Manualshive

Page: 50 / 80

background image

48

Angle Adjustments

SINGLE DISC GANGS

Single Disc Assemblies (06-082-057) are use on
30” Row machine. Assemble Single Disc to the
disc mounting brackets (06-080-008) & (06-080-
081) and set angle.

DISC SCRAPER KIT

A Disc Scraper Kit (06-082-015) is made up of an 18” Disc Scraper and 20” Disc scraper which are
mounted to the disc mounting brackets. The 18” Disc Scraper requires a scraper support (06-023-049)
to mount the scraper to the disc mounting bracket as shown above.

Scraper Support

(06-023-049)

18” Disc Scraper

(06-027-004)

20” Disc Scraper

(06-023-050)

«
...
48
49
50
51
52
...
»

Summary of Contents for 68 Series

















































































Reviews:

No comments

Related manuals for 68 Series

Brand: Raymarine Pages: 464

Brand: 3M Pages: 8

Brand: ZOLL Pages: 3

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: GE Pages: 24

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands