KKT KSC 215-L-U/S, Installing Instruction

Page: 7 / 39

Installing Instruction Installing Instruction Installing Instruction Installing Instruction
Healthcare chiller of the KSC Series
Healthcare chiller of the KSC Series Healthcare chiller of the KSC Series
Healthcare chiller of the KSC Series
Version „Revision 0 Version „Revision 0 Version „Revision 0 Version „Revision 05 5 5 5” ” ” ”
Type KSC 215 Type KSC 215 Type KSC 215 Type KSC 215----L LL L----U/S U/S U/S U/S
page page page page 7 7 7 7von von von von39 39 39 39
U:\KSC 215 L\03_Dokumente\Installationsanleitung\KKT_chillers_Installing_Instruction_engl_Vers05.doc
II. Installation site
II. Installation site II. Installation site
II. Installation site
a) Ambient temperatures
a) Ambient temperatures a) Ambient temperatures
a) Ambient temperatures
The chiller is designed to operate at ambient temperatures between –20°C (-4°F)
minimum and +48°C (+118.4°F) maximum.
Malfunctions can occur outside these specifications.
If the chiller is used at high ambient temperatures (higher than 40°C = 104°F) the the
If the chiller is used at high ambient temperatures (higher than 40°C = 104°F) the the If the chiller is used at high ambient temperatures (higher than 40°C = 104°F) the the If the chiller is used at high ambient temperatures (higher than 40°C = 104°F) the the
chiller should be installed that the
chiller should be installed that the chiller should be installed that the
chiller should be installed that the switch cabinet is not fully exposed to the sun
switch cabinet is not fully exposed to the sun switch cabinet is not fully exposed to the sun
switch cabinet is not fully exposed to the sun
radiation when the maximum ambient temperature is prevent. If th radiation when the maximum ambient temperature is prevent. If th radiation when the maximum ambient temperature is prevent. If th radiation when the maximum ambient temperature is prevent. If this is not possible is is not possible is is not possible is is not possible
please install a sun protection!! please install a sun protection!! please install a sun protection!! please install a sun protection!!
Support from KKT
Support from KKT Support from KKT
Support from KKT chillers
chillers chillers
chillers could be requested.
could be requested. could be requested.
could be requested.
b) Clearance b) Clearance b) Clearance b) Clearance
Maintain at least 100 cm (39.4 in.) around all four sides of the chiller for air intake and
servicing/repair.
Under no circumstances install a roof above the chiller.
c) Servicing and repair access c) Servicing and repair access c) Servicing and repair access c) Servicing and repair access
See Clearance
d) Air flow d) Air flow d) Air flow d) Air flow
Never obstruct the air intake to the condensers on the upper third of the chiller.
The diameter of the tubes may not be smaller than the size specified.
e) Load capacity
e) Load capacity e) Load capacity
e) Load capacity of the base
of the base of the base
of the base
Verify that the installation surface has sufficient load capacity.
A concrete foundation or sectional steel construction is recommended.
A concrete foundation needs to be 200 mm (7.8 in.) wider and 200 mm (7.8 in.) longer
than the cooling block. Final dimensions: approx. 3,200 mm (10.5 feet) long by 1,100
mm (3.6 ft) wide.
The operating weight of the chiller is approx. 1,100 kg (2,425 lbs.).
The operating weight of the chiller is approx. 1,100 kg (2,425 lbs.). The operating weight of the chiller is approx. 1,100 kg (2,425 lbs.).
The operating weight of the chiller is approx. 1,100 kg (2,425 lbs.).
It is important that the cooling block be installed on a level surface.