KitchenAid Ensemble KEHS01PMT/WH Technical Education Download

Page: 26 / 88

2-16

Fire Hazard

Cover unused exhaust holes with the
following kit:

280028 (meteorite)
279818 (white)

Contact your local dealer.

Failure to follow these instructions can
result in death, fire, electrical shock, or
serious injury.

PLAN VENT SYSTEM

Typical Exhaust Installations

Typical installations vent the dryer from the
rear of the dryer. Other installations are pos-
sible.

Optional Exhaust Installations

This dryer can be converted to exhaust out the
right side, left side, or through the bottom.
Contact your local dealer to have the dryer
converted.

Alternate Installations For Close Clearances

Venting systems come in many varieties. Se-
lect the type best for your installation. Two
close-clearance installations are shown. Refer
to the manufacturer’s instructions.

1. Dryer

2. Elbow
3. Wall
4. Exhaust hood
5. Clamps

6. Rigid metal or flexible metal vent

7. Vent length necessary to connect
elbows
8. Exhaust outlet

1. Standard rear offset exhaust installation

2. Left or right side exhaust installation
3. Bottom exhaust installation (Not an option with
pedestal installations.)

1. Over the top installation (also available with one

offset elbow)
2. Periscope installation

WARNING

Summary of Contents for Ensemble KEHS01PMT/WH

























































































Search results

Summary of Contents for Ensemble KEHS01PMT/WH

Reviews:

Related manuals for Ensemble KEHS01PMT/WH

Brands by name

Popular brands

KitchenAid Ensemble KEHS01PMT/WH, Technical Education

Search results

Summary of Contents for Ensemble KEHS01PMT/WH

Reviews:

Related manuals for Ensemble KEHS01PMT/WH

Brands by name

Popular brands