![background image](http://html.mh-extra.com/html/kitchenaid/architect-series-ii-kgrs308x/architect-series-ii-kgrs308x_use-and-care-manual_198057020.webp)
20
Setting Oven Controls
Fig. 1
To set the oven to continue cooking after
reaching the probe target temperature:
1. Press
Meat Probe
keypad and hold for 6 seconds.
2. Press
Self Clean
keypad and toggle until the Continu
message appears (Fig. 2) then press
START
to
accept.
To set the oven to cancel cooking after reaching
the probe target temperature:
1. Press
Meat Probe
keypad and hold for 6 seconds.
2. Press
Self Clean
keypad and toggle until CAnCEL
message appears (Fig. 3) then press
START
to
accept.
The U.S. Department of Agriculture states, Rare fresh
beef is popular, but you should know that cooking it to
only 140°F/60°C means some food poisoning
organisms may survive. (Source: Safe Food Book,
Your Kitchen Guide, USDA Rev. June 1985.)
The lowest temperature recommended by the USDA is
145°F/63°C for medium rare fresh beef.
Fig. 2
Fig. 3
To set meat probe:
1. Prepare the food and properly insert the temperature
probe into the food.
DO NOT PREHEAT
or start
cooking before inserting the meat probe. The probe
should be inserted into the food and receptacle while
the oven is still cool.
2. Place the prepared food on the desired oven rack
position and slide into the oven.
3. Plug the meat probe into the probe receptacle located
on the left front oven cavity side (See Fig. 1 for
location of probe receptacle).
4. The oven control detects if the meat probe is correctly
plugged in to receptacle and when recognized will
illuminate the
icon in the oven control display.
5. To set the target temperature press Meat Probe
keypad once then enter the desired target internal
temperature using the numeric key pads (default
setting is 170ºF/77ºC). Press
START
to accept the
meat probe target temperature. Close the oven door.
6. Set the oven control for Bake, Conv Bake or Conv
Roast and the desired oven temperature. You may use
the meat probe with some other baking features, but
the meat probe cannot be set with Broil or Self Clean.
7. While cooking, the actual meat probe temperature will
display by default. To view the target temperature press
the Meat Probe keypad once. After 6 seconds the display
will return to the actual meat probe temperature. If the
target temperature needs to be changed during the
cooking process, press the Meat Probe keypad once and
use the numeric keypads to adjust the target temperature.
Press the
START
key to accept any change.
8. The oven control will beep three times and turn off when
the internal target temperature is reached. Instructions for
changing how the oven reacts after reaching the internal
target temperature may be found later in this section.
Press
OFF
to cancel cooking at any time.
Important notes:
Use ONLY the meat probe supplied with appliance.
Using any other probe or device may damage the
appliance and the meat probe receptacle.
Never leave or store meat probe inside oven.
Handle the meat probe carefully when inserting and
removing from food or probe receptacle. Do not use
tongs to pull on meat probe cable or to insert or remove
from food or receptacle.
Defrost food completely before inserting meat probe to
avoid damaging probe.
To avoid possibility of burns, after cooking carefully
unplug meat probe using a pot holder to protect hands.
Changing how the oven reacts after reaching the target
temperature must be done before starting the cooking
process.
Summary of Contents for ARCHITECT SERIES II KGRS308X
Page 1: ...Models Modèles KGRS308X W10336759A 316902705 ...
Page 36: ......
Page 37: ...Models Modèles KGRS308X W10336759A 316902705 ...