Kisae Abso Charger 12V 100A Owner'S Manual Download Page 3

 

 

Page 

 

 

 

For safe and optimum performance, the 

KISAE Abso Charger

 must be used properly. Carefully read and 

follow all instructions and guidelines in this manual and give special attention to the 

CAUTION

 and 

WARNING

 

statements. 

 

 

PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE 

 

 

Disclaimer 

While every precaution has been taken to ensure the accuracy of the contents of this guide, 

KISAE 

Technology 

assumes no responsibility for errors or omissions. Note as well that specifications and 

product functionality may change without notice. 
 

Important  

Please be sure to read and save the entire manual before using your 

KISAE Abso Charger. 

Misuse 

may result in damage to the unit and/or cause harm or serious injury.  
 

 
 

 

Product Numbers 

AC12100 

Abso Charger 12V 100A 

AC2450

 

Abso Charger 24V 50A 

 

 

Document Part Number 

 

MU AC12100 Rev A

 

 
Service Contact Information 

Email: [email protected] 
Phone : 1 877 897-5778 
Web 

www.kisaepower.com

  

 

 

 

WARNING: 

This product can expose you to chemicals, including Di (2-ethylhexyl) phthalate (DEHP)

 

which is 

known to the State of California to cause cancer, birth defects or other reproductive

 

harm. For more information, 

go to www.p65warnings.ca.gov

 

ADVERTENCIA 

Este producto puede exponerlo a productos químicos, incluidos Di (2-etilhexil) ftalato (DEHP)

 

que el estado de California sabe que causa cáncer, defectos de nacimiento u otros daños

 

reproductivos. Para 

obtener más información, vaya a www.p65warnings.ca.gov

 

 

Summary of Contents for Abso Charger 12V 100A



























Reviews: