Kioti DK55 Manual Download

Page: 48 / 135

INSTRUMENT PANEL AND CONTROLS 4-17

069O435A

069O436A

OUTER HYDRAULIC CONTROL
LEVER

Attaching or detaching the implements at
external, controls the lift arm position by
this lever.

Outer Hydraulic Control Lever

Operating the hydraulic control lever ac-
tuates the hydraulic lift arm, which con-
trols implement height or working depth.
To lower implement, push the lever
forward; to raise it, pull the lever back.

HYDRAULIC CONTROL LEVER

(1) Position Control Lever (3) Stop Bolt

(2) Draft Control Lever

HOW TO USE THE STOP BOLT

1. Determine a desired working position,

using the control lever.

2. Fix the stop bolt in the desired position.

3. Once the stop bolt is set, simply move

the relevant hydraulic lever forward
until it reaches the stop bolt.

Summary of Contents for DK55








































































































































Search results

Summary of Contents for DK55

Reviews:

Related manuals for DK55

Brands by name

Popular brands

Kioti DK55, Manual

Search results

Summary of Contents for DK55

Reviews:

Related manuals for DK55

Brands by name

Popular brands