manualshive.com logo in svg

Kioti DK55, Manual

Share
Download
Kioti DK55 Manual Download Page 67

THREE-POINT HITCH & DRAWBAR  6-3

069O603A

069O602A

ADJUSTMENT OF CHECK LINKS

Adjust the Check Links to control hori-
zontal sway of the implement.

(1) Check Link

(2) Pin

Type of implement

Plow, furrow,
subsoiler,
cultivator, ditcher

Rotary, mower,
hay rake, tender,
rider

Check Link adjust-
ment

Loosen until the
implement can be
moved 50 ~ 60 mm
(1.97 ~ 2.36 in.)
horizontally.

Tighter

NOTE

DRAWBAR

ADJUSTING DRAWBAR LENGTH

(1) PTO Shaft

(3) Drawbar

(2) Drawbar Pin

(4) Holes

WARNING

To avoid personal injury:

Never pull from the top link, the
rear axle or any point above the
drawbar. Doing so could cause
the tractor to tip over rearward
causing personal injury or death.

When towing an inplement, recommend
use of (4) hole in drawbar.

The drawbar load is referred to “IMPLE-
MENT LIMITATIONS” section.

The rear wheel must not interfere with
the check link or the lower link when
you control the check link.

Summary of Contents for DK55








































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands