background image

31

Parts List

PART NO.

DESCRIPTION

Fireplace Part Numbers

MDV38 SERIES  MULTI-SIDED DIRECT VENT FIREPLACE:

Listed for USA/Canada as a Decorative Appliance, Includes: Triple Burner, Up to
Three Viewing Areas, Milli Volt Sit Valve, Hi/Lo Adjustment, Wall Mount On/Off
Switch, Ember Ash Kit, Four and Seven Flue, Sloped Back, 39,000 BTU NG, 
38,000 BTU LP

MDVR38N

Multi-Sided Fireplace, c/w Right Burner (as above) Natural Gas

MDVR38LP

Multi-Sided Fireplace, c/w Right Burner (as above) Liquid Propane

MDVL38N

Multi-Sided Fireplace, c/w Left Burner (as above) Natural Gas

MDVL38LP

Multi-Sided Fireplace, c/w Left Burner (as above) Liquid Propane

FIREPLACE REQUIREMENTS

Log Sets: (Required for each unit)

LOGF38

Log Set - Five Piece Fibre Split Oak (MDV38)

Choose Your View: (Required for each unit)

M38PK

PENINSULA KIT - THREE SIDED VIEWING

- One Large Panel of Ceramic Glass, One Small Panel of Ceramic Glass

M38CK

CORNER KIT - TWO SIDED VIEWING

- One Small Panel of Ceramic Glass
- One Large Clearance Shield, One Large Solid Door Panel

M38SK

SEE-THROUGH KIT - TWO SIDED VIEWING

- One Large Panels of Ceramic Glass
- One Small Clearance Shield, One Small Solid Door Panel

GRILL KITS: (Required for each unit)

MGPKBP

Grill Kit Peninsula - Classic Polish Brass (Three Sets)

MGPKBA

Grill Kit Peninsula - Classic Antique Brass (Three Sets)

MGPKBC

Grill Kit Peninsula - Classic Chrome (Three Sets)

MGPKBL

Grill Kit Peninsula - Black (Three Sets)

MGPKAB

Grill Kit Peninsula - Antique Brass (Three Sets)

MGPKCR

Grill Kit Peninsula - Chrome (Three Sets)

MGCKBP

Grill Kit Corner - Classic Polish Brass (Two Sets)

MGCKBA

Grill Kit Corner - Classic Antique Brass (Two Sets)

MGCKBC

Grill Kit Corner - Classic Chrome (Two Sets)

MGCKBL

Grill Kit Corner - Black (Two Sets)

MGCKPB

Grill Kit Corner - Polish Brass (Two Sets)

MGCKAB

Grill Kit Corner - Antique Brass (Two Sets)

MGCKCR

Grill Kit Corner - Chrome (Two Sets)

MGSKBP

Grill Kit See-Through - Classic Polish Brass (Two Sets)

MGSKBA

Grill Kit See-Through - Classic Antique Brass (Two Sets)

MGSKBC

Grill Kit See-Through - Classic Chrome (Two Sets)

MGSKBL

Grill Kit See-Through - Black (Two Sets)

MGSKPB

Grill Kit See-Through - Polish Brass (Two Sets)

MGSKAB

Grill Kit See-Through - Antique Brass (Two Sets)

MGSKCR

Grill Kit See-Through -Chrome (Two Sets)

Bay Window Kits: for MDV38 Series Only

Bay Window Kits Consist of Black Upper Grill and Brass Lower Grill, Black Frame,
Three Piece Tempered Glass Viewing Area, and Ember Kit.

Z36BWAB

Bay Window (as above) with Antique Brass Louvres

Z36BWPB

Bay Window (as above) with Polish Brass Louvres

Z36BWCR

Bay Window (as above) with Chrome Louvres

MDV30 SERIES  MULTI-SIDED DIRECT VENT FIREPLACE:

Listed for USA/Canada as a Decorative Appliance, Includes: Triple Burner, Up to
Three Viewing Areas, Milli Volt Sit Valve Featuring less than 30 Sec Shut Down with
Hi/Lo Adjustment, Wall Mount On/Off Switch, Ember Ash One Large Panel of
Tempered Glass, Four and Seven Flue, Sloped Back, 30,000 BTU NG & LP

MDVR30N

Multi-Sided Fireplace, c/w Right Burner (as above) Natural Gas

MDVR30LP

Multi-Sided Fireplace, c/w Right Burner (as above) Liquid Propane

MDVL30N

Multi-Sided Fireplace, c/w Left Burner (as above) Natural Gas

MDVL30LP

Multi-Sided Fireplace, c/w Left Burner (as above) Liquid Propane

Log Sets: (Required for each unit)

LOGF38

Log Set - Five Piece Fibre Split Oak (MDV38)

Choose Your View: (Required for each unit)

M30PK

PENINSULA KIT - THREE SIDED VIEWING

- One Large Panel of Tempered Glass, One Small Panel of Tempered Glass

M30CK

CORNER KIT - TWO SIDED VIEWING

- One Small Panel of Tempered Glass
- One Large Clearance Shield, One Large Solid Door Panel

M30SK

SEE-THROUGH KIT - TWO SIDED VIEWING

- One Large Panel of Tempered Glass
- One Small Clearance Shield, One Small Solid Door Panel

Fireplace Accessories Options:

MDV38IS

Insulation Sleeve 3ft. - for Low Enclosures

MDV38RLE

Refractory Liner - End (Small Panel)

MDV38RLS

Refractory Liner - Side (Large Panel)

Z36SAB

Surround - Antique Brass (Coverage Old Style 33 3/4” H x 39 7/8” W)

Z36SCR

Surround - Chrome (Coverage New Style 34 1/2” H x 41 1/8” W)

Z36SPB

Surround -Polish Brass (Coverage New Style 34 1/2” H x 41 1/8” W)

Z36SLAB

Surround Slim Line - Antique Brass (Coverage 34 1/4” H x 37 1/2” W)

Z36SLCR

Surround Slim Line -Chrome (Coverage 34 1/4” H x 37 1/2” W)

Z36SLPB

Surround Slim Line - Polish Brass (Coverage 34 1/4” H x 37 1/2” W)

Z36SLBL

Surround Slim Line - Gun Metal Black (Coverage 34 1/4” H x 37 1/2” W)

Z1ADBL

Arch Door Frame - Black

Z36ADDX

Arch Door Frame - Deluxe Black  (352)

Z36ADTH

Arch Door Frame - Top Half Black  (353T)

Z36ADDA

Arch Door Frame - Double Arch  Black  (354)

Z36ADDD

Arch Door Frame - Double Door Arch Black  (355)

Z1ADAB

Arch Door Frame - Antique Black

Z36ADCR

Arch Door Frame - Chrome

Z1ADPB

Arch Door Frame - Polish Brass

Z36FK

Fan Kit w/variable Speed Wall Mount Control (Temperature Sensing)

Z1MT

Thermostat Millivolt Wall Mount

Z80PT

Thermostat Programmable Digital Millivolt Wall Mount (1F80-40)

Z1RC

Remote Control Millivolt (On/Off with LED) (Model I)

ZART

Remote Control Thermostat Millivolt (Model K)

DCHS

Remote Control Heatshield

Replacement Burner Assembly

3800-BRNG

Burner Assembly - Right, Natural Gas - For Model MDVR38N

3800-BRLP

Burner Assembly - Right, Liquid Propane - For Model MDVR38LP

3800 - BLNG

Burner Assembly - Left, Natural Gas - For Model MDVL38N

3800-BLLP

Burner Assembly - Left, Liquid Propane - For Model MDVL38LP

3000-BRNG

Burner Assembly - Right, Natural Gas - For Model MDVR30N

3000-BRLP

Burner Assembly - Right, Liquid Propane - For Model MDVR30LP

3000-BLNG

Burner Assembly - Left, Natural Gas - For Model MDVL30N

3000-BLLP

Burner Assembly - Left, Liquid Propane - For Model MDVL30LP

Summary of Contents for MDVL30LP





































Reviews: