background image

 

5

14. Welding 

timer: 

The time during which the ultrasonic wave is transmitting. 

15. Curing 

Timer: 

The time from stopping the ultrasonic transmission to when the vibrating cylinder 

rises. During this time, the plastic is curing from its molten state with the pressure 

being exerted on the work-piece. 

16. Selector 

Switch: 

a. Manual 

Operation: 

When the operator presses two push buttons simultaneously with two hands, the 

welding head drops together with the vibrating cylinder and remains at the drop 

position. The welding head will rise together with the vibrating cylinder when 

the emergency rise button is pushed. 

b. Automatic 

Timing 

Operation: 

When the operator presses two push buttons simultaneously with two hands, the 

delay-on, melting, and curing timing operations will be carried out automatically. 

c.  Sonic Wave Inspection: Check if the ultrasonic wave is transmitted appropriately.   

Note:

 Remember that the knob should not be set to the ultrasonic wave 

inspection position when the power cord is unplugged. 

17. Counter: 

Record the operating times of the work-piece. Press the black button to zero the 

counter. 

18. Rise 

Governor: 

Rotate it anti-clockwise to increase the rise speed or rotate it clockwise to decrease 

the rise speed of the vibrating cylinder.   

Note:

 The nut between knobs is used to lock the governor and should be tightened 

after adjustment. 

19. Drop 

Governor: 

Rotate it anti-clockwise to increase the drop speed or rotate it clockwise to decrease 

the drop speed of the vibrating cylinder. 

Note:

 Refer to 18. 

20. Hand 

Wheel: 

After loosening two fixed handles and rotating the hand wheel, the body will rise or 

drop alongside the large column to adjust the height of the welding head. 

21. Fixed 

Screw: 

After the four fixed screws are loosened, the welding head can be rotated and 

tightened after being aligned with the direction of the work-piece. 

22.  Operator Push Buttons: 

When two operator push buttons are pressed with both hands, the system operates in 

accordance with the setting of the selector switch. 

Note: 

Do not push one button with a toothpick or sharp-edged object for 

Summary of Contents for KWL3215


























Reviews: