King Long XMQ6129Y series Operating Manual Download Page 43

Page: 43 / 161

Technical parameter and complete vehicle description

0-T-1

system error. The vehicle cannot be
driven.

◆

» = clutch

◆

Alternates with the normal display.

Clutch is overloaded.

◆

Remedy: chapter 2.13 clutch protection

◆

» = clutch wear

◆

Proceed to approved workshop to have



clutch exchanged at next opportunity.

◆

» = High temperature

(too high transmission temperature)

◆

» = Electronic Error

◆

Is displayed when the communication

of the display with the transmission
electronics is disturbed.

System error:

◆

Spanner

» = system error

◆

Appears if the operations are only

available with restrictions.

◆

Visit a specialist workshop as soon as

possible.

NOTE

Summary of Contents for XMQ6129Y series


































































































































































Search results

Summary of Contents for XMQ6129Y series

Reviews:

Related manuals for XMQ6129Y series

Brands by name

Popular brands

King Long XMQ6129Y series, Operating Manual

Search results

Summary of Contents for XMQ6129Y series

Reviews:

Related manuals for XMQ6129Y series

Brands by name

Popular brands