King Long XMQ6129Y series Operating Manual Download Page 38

Page: 38 / 161

Technical parameter and complete vehicle description

0-T-1



Turn rotary switch to «

».



« R » appears in the display

(clutch remains separated
(disengaged)).



Depress accelerator and

at the same time, release
brake (clutch closes
automatically).



Vehicle moves backwards.

DANGER !

If the vehicle is rolling, shifts cannot be made into

reverse!

Stop the vehicle immediately.

1.8 Changing direction of travel

Changing from reverse «

» to forwards travel «

and vice versa.

DANGER !

A change in the direction of travel, performed by

moving the rotary switch from « R » to « D » and vice

versa « D » to « R », may only be undertaken when

the vehicle is at a standstill otherwise the

transmission will shift into neutral.

Only refer to the display for the direction of travel

selected in the transmission.

Summary of Contents for XMQ6129Y series


































































































































































Search results

Summary of Contents for XMQ6129Y series

Reviews:

Related manuals for XMQ6129Y series

Brands by name

Popular brands

King Long XMQ6129Y series, Operating Manual

Search results

Summary of Contents for XMQ6129Y series

Reviews:

Related manuals for XMQ6129Y series

Brands by name

Popular brands