background image

Kieback&Peter GmbH & Co. KG
Tempelhofer Weg 50, 12347 Berlin/Germany
Telefon: +49 30 60095-0, Telefax: +49 30 60095-164
www.kieback-peter.de, [email protected]

MD15-C, MD15-HR, MD15-DA

3.09-20.115-01-EN | 2019-08-12

Q

Product Description

MD15-C, MD15-HR and MD15-DA Actuators

For Rxx, RWxx valves and Danfoss RA Series 

Application

The MD15-C, MD15-HR and MD15-DA actuators for three-point, 
two-point or continuous closed-loop control in zone post-treatment 
devices for heating, ventilation and air conditioning systems.

Content

Page

Important Information Regarding Product Safety ..................................................................................................2
MD15-C, MD15-HR and MD15-DA Actuators .......................................................................................................3

Technical Data.....................................................................................................................................................3
Dimensions ..........................................................................................................................................................4
Connection...........................................................................................................................................................5

Valve Installation....................................................................................................................................................6
Mounting and Commissioning the Actuator ...........................................................................................................7
Dismounting the Actuator ....................................................................................................................................11
Manual adjustment ..............................................................................................................................................13
Commissioning ....................................................................................................................................................14

Summary of Contents for MD15-C















Reviews: