background image

at a minimum of 4” (10 cm) and a maximum of 12” (30.5 cm) 
below the ceiling (see figure 1).

•  Install Smoke Alarms on sloped, peaked or cathedral ceilings at or 

within 3ft (0.9m) of the highest point (measured horizontally).  NFPA 
72 states: “Smoke alarms in rooms with ceiling slopes greater than 1 
ft in 8 ft (.3m in 2.4 m) horizontally shall be located on the high side 
of the room.” NFPA 72 states: “A row of detectors shall be spaced 
and located within 3 ft (0.9m) of the peak of the ceiling measured 
horizontally” (see figure 2).

•  Install Smoke Alarms on tray-shaped ceilings (coffered ceilings) on 

the highest portion of the ceiling or on the sloped portion of the ceil-
ing within 12” (305mm) vertically down from the highest point (see 
figure 4).

Mobile Home Installation

Modern mobile homes have been designed and built to be energy 
efficient. Install smoke alarms as recommended above (refer to 
RECOMMENDED LOCATIONS and Figures 1 and 2). In older mobile 
homes that are not well insulated compared to present standards, 
extreme heat or cold can be transferred from the outside to the inside 
through poorly insulated walls and roof. This may create a thermal bar-
rier which can prevent the smoke from reaching an alarm mounted on 
the ceiling. In such units, install the smoke alarm on an inside wall with 
the top edge of the alarm at a minimum of 4” (10cm) and a maximum 
of 12” (30.5cm) below the ceiling (see figure 1).

If you are not sure about the insulation in your mobile home, or if you 
notice that the outer walls and ceiling are either hot or cold, install 
the alarm on an inside wall. For minimum protection, install at least 
one alarm close to the sleeping rooms. For additional protection, see 
SINGLE FLOOR PLAN in figure 2.

WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER 
RV OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, 
BEFORE EACH TRIP AND AT LEAST ONCE A WEEK DURING 
USE.

2. LOCATIONS TO AVOID

•  In the garage. Products of combustion are present when you start    
 your 

automobile.

•  Less than 4” (10cm) from the peak of an “A” frame type ceiling.

•  In an area where the temperature may fall below 40ºF or rise above 

100ºF, such as garages and unfinished attics; this should also include 
electrical boxes exposed to these environments.

•  In dusty areas. Dust particles may cause nuisance alarm or failure 

to alarm.

1475-7205-00(820-0905-EN)_R1.indd   4

1475-7205-00(820-0905-EN)_R1.indd   4

2009.12.9   10:07:37 AM

2009.12.9   10:07:37 AM

Summary of Contents for PI 2000

















Reviews: