KICE Pneu-Jet Filter Operator'S Manual Download Page 36

36

Kice Industries, Inc.

FLT-M03-0002

012420

Appendix B Continued

Page 2 of 6                                                                                     

I&M No. V_6584_R19_sec1   

 

©

ASCO Valve, Inc.

 

50 Hanover Road, Florham Park, New Jersey 07932             www.ascovalve.com  

¹ =  EF, EV data applies to Explosionproof coils only. 

² = Some DC solenoid valves can be operated at maximum ambient 

temperature of 55°C / 131°F with reduced pressure ratings. See 

valve I&M for maximum operating pressure differential ratings. 

³ = Steam Service Valves have a maximum ambient temperature of 55° 

C/ 131°F. 

CAUTION: To protect the solenoid valve or 

operator,  install  a  strainer  or  filter,  suitable  for  the 

service involved in the inlet side as close to the valve 

or operator as possible. Clean periodically depending 

on service conditions. See ASCO Series 8600 and 8601 

for strainers.

ATTENTION  :  Afin  de  protéger  l’électrovanne  ou 

l’actionneur, installer une crépine ou un filtre adapté 

le plus proche possible en amont de l’électrovanne ou 

de  l’actionneur.  Nettoyer  périodiquement  le  filtre  en 

fonction des conditions d’utilisation. Se référer aux 

séries 8600 et 8601 pour les crépines.  

Temperature Limitations 

For maximum solenoid ambient temperatures, refer to chart. 

The temperature limitations listed, only indicate maximum 

application temperatures for field wiring rated at 90

°

C. Check 

catalog number prefix and watt rating on nameplate to determine 

maximum ambient temperature. See valve installation and 

maintenance  instructions  for  maximum  ambient  and  fluid 

temperatures. 

NOTE: 

 For steam service, refer to 

Wiring

 section, 

Junction Box

 

for temperature rating of supply wires.  

§ Minimum ambient temperature -40°F (-40°C).  

Positioning

This solenoid is designed to perform properly when mounted in 

any position. However, for optimum life and performance, the 

solenoid should be mounted vertically and upright to reduce the 

possibility of foreign matter accumulating in the solenoid base 

sub-assembly area.

Wiring 

Wiring must comply with local codes and the National Electrical 

Code. All solenoids supplied with lead wires are provided with a 

grounding wire which is green or green with yellow stripes and 

a 1/2˝ conduit connection. To facilitate wiring, the solenoid may 

be rotated 360

°

.  For explosionproof solenoid version, the conduit 

lead wires are factory sealed for use in hazardous locations.   

    CAUTION: Cryogenic Applications - Solenoid lead 

wire insulation should not be subjected to cryogenic 

temperatures.  Adequate lead wire protection and 

routing must be provided.

ATTENTION: Application cryogénique. Les 

câbles électriques ne doivent pas être soumis à des 

températures cryogéniques. Une protection adequate 

des cables électriques doit être fournie.

Additional Wiring Instructions For Optional Features: 

• 

Open-Frame solenoid with 1/4˝ spade terminals.

 

For solenoids supplied with screw terminal connections use #12-

18 AWG stranded copper wire rated at 90

°

C or greater. Torque 

terminal block screws to 10±2 in-lbs [1,0±1,2 Nm]. A tapped hole 

is provided in the solenoid for grounding, use a #10-32 machine 

screw. Torque grounding screw to 15-20 in-lbs [1,7-2,3 Nm]. On 

solenoids with screw terminals, the socket head screw holding the 

terminal block to the solenoid is the grounding screw. Torque the 

screw to 15-20 in-lbs [1,7-2,3 Nm] with a 5/32˝ hex key wrench.  

• 

Junction Box 

The junction box is used with spade or screw terminal solenoids 

only and is provided with a grounding screw and a 1/2˝ conduit 

connection. Connect #12-18 AWG standard copper wire only to 

the screw terminals. Within the junction box use field wire that 

is rated 90

°

C or greater for connections. For steam service use 

105

°

C rated wire up to 50 psi or use 125

°

C rated wire above 

50 psi. After electrical hookup, replace cover gasket, cover, and 

screws. Tighten screws evenly in a crisscross manner

Temperature Limitations for Series 8003H, 8007H and 8202H 

solenoids

Watt Ratings

Maximum Ambient 

Temperature

Prefix ¹

Coil 

Class

AC

DC

60 Hz

50 Hz

°C

°F

EF, EV

FT

10.1

10.1

-

52

125

EF, EV

FB

17.1

17.1

-

FT

10.1

10.1

-

55

131

FB

17.1

17.1

-

HT

-

-

11.6

40 ²

104 ²

HF

-

-

15.6

HB

-

-

22.6

EF, EV

HT

-

-

11.6

EF, EV

HF

-

-

15.6

EF, EV

HB

-

-

22.6

HT

10.1

10.1

-

60 ³

140 ³ 

HB

17.1

17.1

-

EF, EV

HT

10.1

10.1

-

EF, EV

HB

17.1

17.1

-

EF, EV

HC

-

-

24.6

Multipin Connector

Connector Type

Mating Connector

Application

VT / VB

4-Pin, M12, Female, Single Keyway

DC

4-Pin, M12, Female, Dual Reverse 

Keyway

AC

ZT / ZB

3-Pin, Mini, Female, Single Keyway

AC / DC

• 

 

DIN Plug Connector Kit No. K236034 

1. 

The open

-

frame solenoid is provided with DIN terminals 

to accommodate the plug connector kit. 

2. 

Remove center screw from plug connector. Using a small 

screwdriver, pry terminal block from connector cover. 

3. 

Use #12

-

18 AWG stranded copper wire rated at 90

°

or greater for connections. Strip wire leads back 

approximately  1/4˝  for  installation  in  socket  terminals. 

The use of wire

-

end sleeves is also recommended for 

these  socket  terminals.  Maximum  length  of  wire

-

end 

sleeves to be approximately 1/4˝. Tinning of the ends of 

the lead wires is not recommended. 

4. 

Thread wire through gland nut, gland gasket, washer and 

connector cover. 

NOTE:

 Connector housing may be rotated in 90

°

 increments 

from position shown for alternate positioning of cable entry. 

Temperature Limitations For Series 8003G, 8007G or 8202G

Watt

Rating

Catalog

Number Coil Prefix

Class of

Insulation

Maximum §

Ambient Temp.

10.1 & 17.1

None, FB, KF, KP,

SC, SD, SF, SP, VT, VB, 

ZT & ZB 

F

125°F (52°C)

10.1, 17.1  &  

24.6

HB, HT, KB, KH, SS, ST, 

SU, HC

H

140°F (60°C)

11.6 & 22.6

None, FB, KF, KP,

SC, SD, SF, SP, VT, VB, 

ZT & ZB

F

104°F (40°C)

11.6 & 22.6

HP, HT, KB, KH,

SS, ST, SU & SV

H

104°F (40°C)

15.6

None, KB, SS, SV

H

104°F (40°C)

Summary of Contents for Pneu-Jet Filter











































Reviews: