background image

Lancaster

®  

Auditorium Seating with Power & Data

Assembly Instructions

Assemble units as described herein only. To do otherwise 
may result in instability. All screws, nuts and bolts must be  
tightened securely and must be checked periodically after  
assembly. Failure to assemble properly, or to secure parts 
may result in assembly failure and personal injury.

13

ADA Removable Base

Note:

 ADA removable bases are 

not available with power & data. 

The instructions below detail the 

installation of the uprights to the

ADA removable base using the 

glides, nuts and caps provided. 

It is important to follow the 

assembly instructions during 

assembly.

1. Insert glides up through the  

ADA base and the mounting 

holes in the foot of each upright  

(Figure 16). Secure the 

components together with 

 

5

16

” hex nuts on the glides. 

2. Place a plastic dome cap on top 

of each glide stem, above the 

installed 

5

/

16

” hex nut (Figure 12).

3. Follow instructions for back 

attachment and seat attachment as 

described previously (Figures 3,

4, 5, and 15). If equipped with 

accessories like tablet arms or 

end panels, refer to those sections 

of the assembly instructions.

4. Place the assembled ADA 

removable base/Lancaster Seating 

assembly in the desired location 

for mounting to the floor. Mark the 

location of the mounting holes on 

the floor and move the unit out of 

the way for drilling.

5. Drill mounting holes and install 

anchoring hardware in the floor.

Anchoring hardware is not 

provided. Follow the appropriate 

requirements.

6. Reposition the unit and secure 

to the floor following the floor 

fastener requirements (Figure 17).

7. For removal of the unit, remove 

the hardware that anchors the

ADA base to the floor and move 

the unit. To reinstall, repeat  

step 5.

Note:

 Take great care when 

removing and installing the unit.

Damage to the anchoring 

hardware may result in expensive 

repairs to the floor and anchoring 

hardware.

Caution:

 Unit must be properly 

fastened to the floor. Failure to 

properly fasten unit to the floor 

may result in instability of the unit 

and personal injury.

plastic

dome

cap

Summary of Contents for Lancaster Auditorium Seating





















Reviews: