Keysight Technologies N5241AU-922 Manual Download Page 27 | Manualshive

Page: 27 / 42

background image

Installation Note N5242-90003 27

Description of the Upgrade
Installation Procedure for the Upgrade

Install the following cables in the order listed. Use a 5/16-in torque wrench set

to 10 in-lbs to tighten all cable connectors.

— W95 (N5242-20269) A46 port 1 mechanical switch (connector 2) to W3

(from A5 26.5 GHz source 1 board)

— W96 (N5242-20264) A46 port 1 mechanical switch (connector 3) to A25

test port 1 bridge

— W97 (N5242-20287) A46 port 1 mechanical switch to (connector 1)

rear-panel PORT 1 SW SRC OUT (J11)

— W98(N5242-20288) Rear-panel PORT 1 COMB THRU IN (J10) to A50

combiner

— W99(N5242-20289) Rear-panel PORT 1 COMB ARM IN (J9) to A50

combiner

— W100(N5242-20265) A50 combiner to A46 port 1 mechanical switch

(connector 4)

— W101(N5242-20266) W5 (from A8 26.5 GHz source 2 board) to A47 SRC 2

mechanical switch (connector 2)

— W103(N5242-20282) A47 SRC 2 mechanical switch (connector 1) to

rear-panel SRC 2 SW SRC OUT (J8)

— W104(N5242-20281) Rear-panel PORT 3 SW TSET IN (J7) to A47 SRC 2

mechanical switch (connector 4)

— W109(N5242-20268) W9 (from A5 26.5 GHz source 1 board) to A49 port 2

mechanical switch (connector 2)

— W25(N5222-20038) A28 port 2 bridge to front-panel REF 2 SOURCE OUT

Secure W25 to the side of the deck with 1x cable tie wrap, part number

1400-0249 (included in the kit).

— W154 (N5242-20308) front panel REF 2 RCVR R2 IN to A23 mixer brick (R2)
— W110 (N5242-20262) A49 port 2 mechanical switch (connector 3) to A28

test port 2 bridge

— W111(N5242-20285) A49 port 2 mechanical switch (connector 1) to

rear-panel PORT 2 SW SRC OUT (J2)

— W112(N5242-20286) Rear-panel PORT 2 SW TSET IN (J1) to A49 port 2

mechanical switch

(connector 4)

— W68(N5242-20291) W7 (from A8 26.5 GHz source 2 board) to front-panel

SRC 2 OUT 2

— W67(N5242-20290) A47 SRC 2 mechanical switch (connector 3) to

front-panel SRC 2 OUT 1

«
...
25
26
27
28
29
...
»

Summary of Contents for N5241AU-922











































Reviews:

No comments

Related manuals for N5241AU-922

Brand: Vcheck Pages: 31

Brand: Eagletone Pages: 2

Brand: GE Pages: 8

Moisture Image 1 Series

Brand: GE Pages: 110

DigitalFlow GS868

Brand: GE Pages: 74

DigitalFlow GS868

Brand: GE Pages: 81

Brand: Baker Hughes Pages: 59

Brand: Baker Hughes Pages: 2

Brand: Panametrics Pages: 67

Brand: Panametrics Pages: 108

Transport PT878

Brand: GE Pages: 97

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 4

Brand: Hanna Instruments Pages: 2

Brand: M-system Pages: 13

Brand: Keysight Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands