Keysight Technologies N5241AU-922 Manual Download Page 20 | Manualshive

Page: 20 / 42

background image

20 Installation Note N5242-90003

Description of the Upgrade
Installation Procedure for the Upgrade

-

3.

Connect the other end of gray flex cable W57 on the A13 13.5 GHz

synthesizer board to the J7 connector on the A10 frequency reference

board as shown.

4.

Connect cable W2 between the A8 26.5 GHz source 2 board and the A13

13.5 GHz source 2 synthesizer board as shown. Be sure to position the

cable in the wire looms as shown. Tighten the cable connectors to 10
in-lbs using a 5/16-in torque wrench.

The three 13.5 GHz Synthesizer boards included in this kit are the RoHS

compliant N5240-60076 boards. These new boards are not compatible

with the old N5230-60002 13.5 GHz Synthesizer boards. If the boards

installed in your PNA are the old N5230-60002, you must replace ALL of

them with the N5240-60076 boards included in this kit - refer to your PNA

Service Guide’s chapter 7 for instructions. If your PNA already contains the

new boards, scrap the two extra N5240-60076 boards included in this kit.

For the new N5240-60076 boards to function properly in your PNA, you

must upgrade your PNA firmware to rev A09.33xx or above. Download PNA

http://na.support.keysight.com/pna/firmware/firmware.html

«
...
18
19
20
21
22
...
»

Summary of Contents for N5241AU-922











































Reviews:

No comments

Related manuals for N5241AU-922

Brand: ABB Pages: 20

Brand: Utilitech Pages: 2

Brand: Eaton Pages: 53

Brand: Oceanic Pages: 75

Power Xpert PXM 4000

Brand: Eaton Pages: 28

Brand: Hach Pages: 145

Brand: Hach Pages: 358

Polymetron 9582sc

Brand: Hach Pages: 280

Brand: HACH LANGE Pages: 15

Stage Piano MP8

Brand: Kawai Pages: 70

Brand: WalkLAB Pages: 16

Brand: Yamaha Pages: 31

Brand: Omega Pages: 170

Pasport PS-2138

Brand: Pasco Scientific Pages: 26

Brand: SKF Pages: 12

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

Brand: Sonel Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands