Keysight Technologies N5241AU-922 Manual Download Page 8

Page: 8 / 42

8 Installation Note N5242-90003

Description of the Upgrade
Items Included in the Upgrade Kit

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any part is missing or

damaged, contact Keysight Technologies. Refer to

“Getting Assistance from

Keysight” on page 4

Table 1

Contents of Upgrade Kit N5242-60102

Ref

Desig.

Description

Qty

Part Number

Installation note (this document)

N5242-90003

Software Entitlement Certificate

5964-5145

26.5 GHz source 2 board

5087-7837

A13

13.5 GHz source 2 synthesizer board

N5240-60076

A46

Port 1 mechanical switch

N1811-60028

A47

SRC 2 OUT mechanical switch

A49

Port 2 mechanical switch

A50

Combiner (bridge)

5087-7757

Switch bracket

N5242-00009

Machine screw, M2.5 x 20, pan head (to attach mechanical switch to switch bracket)

0515-1992

Machine screw, M3.0 x 20, pan head (to attach combiner to switch bracket)

0515-1410

Machine screw, M3.0 x 6, pan head (to attach switch bracket to analyzer)

0515-0430

Bulkhead connector assembly for rear panel and front panel

1250-3805

Termination, 50 ohm (for rear-panel PORT 3 SW TSET IN (J7)

1250-4261

Bulkhead connector (front-panel SRC 2 OUT 1 and SRC 2 OUT 2)

08673-60040

Washer (for bulkhead connector 2190-0016)

2190-0016

Hex nut (for bulkhead connector 2190-0016)

2950-0001

Cable tie wrap

1400-0249

Lower front panel overlay (Option 224) – Option 224

N5242-80002

Lower front panel overlay (Option 224) – Option 224 with 029

N5242-80011

RF cable, A13 13.5 GHz source 2 synthesizer J1207 to A8 26.5 GHz source 2 P1

N5222-20090

RF cable, A8 26.5 GHz source 2 to W101

N5222-20062

RF cable, A8 26.5 GHz source 2 to W68

N5222-20063

W25

RF cable, front-panel REF 2 SOURCE OUT to A28 port 2 bridge

N5222-20038

W57

RF flex cable, A10 frequency reference board J7 to A13 13.5 GHz source 2 synthesizer

N5242-60030

W67

RF cable, A47 SRC 2 mechanical switch to front-panel SRC 2 OUT 1

N5242-20290

Summary of Contents for N5241AU-922











































Search results

Summary of Contents for N5241AU-922

Reviews:

Related manuals for N5241AU-922

Brands by name

Popular brands

Keysight Technologies N5241AU-922, Manual

Search results

Summary of Contents for N5241AU-922

Reviews:

Related manuals for N5241AU-922

Brands by name

Popular brands