Keysight Technologies N5221BU-605 Installation Note Download Page 19

Page: 19 / 88

Installation Note N5222-90114

Installation Procedure for the Upgrade

If all of the boards are version H or greater, proceed to

“Step 5. Remove

the Front Panel Assembly”

Else, you need to remove the synthesizer boards and proceed to step

Removing the synthesizer boards for upgrading:

For instructions, click the Chapter 7 bookmark “Removing and Replacing the

A4-A13 Boards” (i.e., refer to your PNA’s serial number prefix section) in the
PDF Service Guide

Save all mounting hardware (except the stabilizer bracket) for reuse.
Refer to

Appendix A:, “Synthesizer Board Upgrade (N5240-60074 (with

Tabs)/N5240-60076 (Without Tabs) Version F/G to Version H),” on page A-1

Step 5. Remove the Front Panel Assembly

For instructions, click the Chapter 7 bookmark “Removing and Replacing the
Front Panel Assembly” in the PDF Service Guide

Step 6. Remove the A19 Test Set Motherboard

For instructions, click the Chapter 7 bookmark “Removing and Replacing

the A

test set motherboard” in the PDF Service Guide1.

IMPORTANT!

This step includes disconnecting and laying aside several

gray cables. Ensure that they are labeled.

1. See

“Downloading the Online PNA Service Guide” on page 8

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands