Keysight Technologies N5221BU-605 Installation Note Download Page 26 | Manualshive

Page: 26 / 88

background image

26 Installation Note N5222-90114

Installation Procedure for the Upgrade

-

Step 13. Remove Some Bottom-Side Semi-Rigid Test Set Cables

1. Place the analyzer bottom-side up on a flat surface.
2. Remove the following cables. To see an image showing the location of

these cables, click the Chapter 6 bookmark “Bottom RF Cables, Standard

2-Port Configuration, Option 205

(S/N Prefixes

<

6021)” in the PDF Service

Guide

1

.

These cables may be discarded - they will not be reinstalled.

— W188 (N5222-20124) A32 port 2 coupler to front-panel Port 2 A74 bias T

combiner

— W117 (N5222-20071) A32 port 2 coupler to front-panel Port 2 CPLR ARM
— W70 (N5222-20073) A21 HMA26.5 to A23 mixer brick
— W12 (N5222-20068) Port 1 CPLR THRU to A29 port 1 coupler
— W12 (N5222-20068) Port 1 CPLR THRU to A29 port 1 coupler
— W182 (N5222-20123) A29 port 1 coupler to front-panel Port 1 A71 bias T

combiner

— W24 (N5222-20069) Port 2 CPLR THRU to A32 port 2 coupler

Be careful not to damage the center pins of the semirigid cables. Some

flexing of the cables may be necessary but do not over-bend them.

Leave the gray flexible cables, the wire harnesses, and the ribbon cables

connected where possible. Any that are removed should be labeled for

reconnection later.
Remove and save the cable guards for the front panel jumpers.
When removing a cable, also remove the plastic cable clamp, if present. It

is normal for some of the cable clamp’s adhesive to remain.

1. See

“Downloading the Online PNA Service Guide” on page 8

These flexible cables have been removed in previous steps:

—

W149 (N5247-60023) A20 IF multiplexer board P603 to A12 SPAM board J2
(2-port)

— W150 (N5247-60024) A20 IF multiplexer board P203 to A12 SPAM board J5

(2-port)

— W64 (N5242-60025) A23 mixer brick (R1) to A20 IF multiplexer (P601)

—

W65 (N5242-60026) A23 mixer brick (R2) to A20 IF multiplexer (P801)

«
...
24
25
26
27
28
...
»

Summary of Contents for N5221BU-605

























































































Reviews:

No comments

Related manuals for N5221BU-605

Brand: Olympus Pages: 86

Brand: CAE Healthcare Pages: 108

Brand: Cannon Pages: 36

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

Brand: DB Industries Pages: 60

Brand: vc999 Pages: 55

Brand: Salsbury Industries Pages: 4

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Gaspardo Pages: 88

Brand: Abbott Pages: 64

Brand: Gako Pages: 22

Brand: ABB Pages: 38

Dome OnTop Weight

Brand: ABS Pages: 8

Brand: Kärcher Pages: 148

bionic power knee

Brand: Össur Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands