background image

Battery Usage 

A fully charged battery should last about four hours. 
Battery charge status is viewable:  

 

In the upper-right corner of the screen. 

 

 

On the battery. To view the LCD gauge on the 
Inspired Energy battery, open the FieldFox battery 
compartment door.  

To conserve battery power: 

 

Use 

Hold

 mode to trigger a measurement only when 

needed. 

Hold

 is shown on the display. 

 

Press 

System

 then 

Display

 then 

Brightness

 then 

dim the FieldFox display as much as possible. 

 

Briefly press the power button to switch to Stand by 
mode when not being used. Press again to restore 
power. All current settings are preserved.  

The FieldFox will shutdown automatically when battery 
power is very low to prevent it from being completely 
discharged.  
Use ONLY a FieldFox charger to recharge a battery. 
The battery can be fully charged while in the FieldFox in 
about 4 hours with the FieldFox either ON or OFF.   
A fully discharged battery takes about 1.5 hours to 
recharge to 80%. 
The battery can be fully charged in about 4 hours using 
the external battery charger (Opt 872).  
 

 

Summary of Contents for FieldFox N9927-90002

















Reviews: