background image

TBC  OPR 071019

2-1

SECTION 2 - INSTALLATION

2.1

UNPACKING AND INSPECTION

This instrument has been thoroughly inspected and tested prior to packing and is ready for
operation. After unpacking, inspect for shipping damage before attempting to operate. Perform
the preliminary inspection as outlined in the following paragraph. If any indication of damage is
found, file an immediate claim with the responsible transport service. 

2.2

TERMINATIONS, CONTROLS AND INDICATORS

a.

Front Panel: 

See Table 2-1 for a description of front panel controls and indicators.

Refer to Figure 2-1 for all models except TBC 24-120M and TBC 48-60M. Refer to Fig-
ure 2-2 for TBC 24-120M and TBC 48-60M. 

TABLE 2-1.  FRONT PANEL CONTROLS AND INDICATORS

FIG. 2-1 

OR FIG. 2-2

INDEX NO.

NAME

FUNCTION

1

POWER ON/OFF

circuit breaker

Main AC input power circuit breaker.

2

VOLTS,

LCD display (2)

3-1/2 digit LCD meter for reading voltage.

3

AMPS

LCD display

3-1/2 digit LCD meter for reading current.

4

EQUALIZE  TIME

timer

0.1 to 99.9 hour timer that can be set to establish the duration of the Equalize 
cycle. 

5

START

switch

Pressing START button starts the EQUALIZE TIME timer as the Equalize mode 
begins. 

6

RESET

switch

Pressing RESET button resets the EQUALIZE TIME timer as the TBC returns to 
the Float mode. 

7

CHARGING STOPPED

indicator

Red LED to indicate that the TBC has stopped charging.

8

EQUALIZE

adjustment control

Screwdriver adjustment of equalize voltage.

9

EQUALIZE

indicator

Amber LED that flashes when the TBC is in the Equalize mode (high rate of 
charging).

10

VOLTAGE ADJUST

lock

A sliding plate behind the panel allows access to the Float and Equalize voltage 
controls. For precise settings of these controls refer to the battery's manufacturer.

11

FLOAT

adjustment control

Screwdriver adjustment of float voltage.

12

FLOAT

indicator

Green LED to indicate when the TBC is in the Float mode (slow rate of charging). 

13

POWER ON

indicator

Green LED power on indicator. 

14

POWER ON/OFF

Locking Plate

Prevents accidental shutoff of TBC. See PAR. ?? for details.

Summary of Contents for TBC 12-50M























Reviews: