Kenwood VRS-5100, Instruction Manual

Page: 16 / 32

16
EN
!
Press the SET UP key again to accept the setting.
• The Subwoofer Remix setting indication ”REMIX” appears.
• If Subwoofer is turned off, subwoofer re-mix setting is not visible.
@
Use the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to
select the appropriate Subwoofer re-mix setting.
1
REMIX ON : Subwoofer re-mix setting mode to
the amplifier is ON.
2
REMIX OFF : Subwoofer re-mix setting mode to
the amplifier is OFF.
When “REMIX ON” is selected, bass sound of other channel
will be added into Subwoofer or bass sound of Subwoofer
will be added into other channel to increase deep bass
performance.
#
Press the SETUP key again to return to the
2
.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
• In steps
5
and
6
, indications appear only for the selected
channels of the speakers that require adjusting.
1
Press the SETUP key and then use the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to select TESTTONE.
2
Press the SETUP key for the following displays:
The selection of AUTO or MANUAL is done by the MULTI
CONTROL
∞¥5
keys or TRIM
∞
/
5
keys.
1
AUTO
2
MANUAL
3
Press the SETUP key again to begin TESTTONE.
Use the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to
adjust the volume level of the test tone output from the
speaker channel to be adjusted.
For AUTO selection, the first test tone is heard from the front left
speaker for 2 seconds. The next test tone is heard from the
speakers in the following sequence for 3 seconds each.
• If you have selected BS/SW BS as the 6ch AMP setting, “RB”
and “LB” are not appeared but “BS” is appeared on the Display.
The channel indication blinks while the test tone is being output.
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
For “MANUAL” selection, press the FRONT, CENTER, REAR
or SW keys to select the speaker channel and then adjust the
volume level by pressing MULTI CONTROL
∞¥5
keys or
TRIM
∞
/
5
keys.
Preparing for surround sound
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL
II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
L C R RS
RB
LB LS SW
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL
II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
• Press the FRONT key each time to select Front L or Front R
channel.
• Press the CENTER or SW key to select Center or Subwoofer
channel.
• Press the REAR key to select Surround and Surround Back
channel.
And use the
REAR key for the following displays.
1
RS : Surround R channel.
2
RB : Surround Back R channel.
3
LB : Surround Back L channel.
4 LS : Surround L channel.
• If you have selected BS/SW BS as the 6ch AMP setting, “RB”
and “LB” are not appeared but “BS” is appeared on the Display.
4
Press the SETUP key again.
• The test tone is turned off and return to the main setup
displays.
6
Input the distance to the speakers.
1
Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to Front Left speaker (L) : ____ meters (feet)
Distance to Center speaker (C) :____ meters (feet)
Distance to Front Right speaker (R) : ____ meters (feet)
Distance to Surround Right (RS) :____ meters (feet)
Distance to Surround Back R Channel (RB):____ meters (feet)
Distance to Surround Back (BS) : ____ meters (feet)
Distance to Surround Back L Channel (LB) :____ meters (feet)
Distance to Surround Left (LS) : ____ meters (feet)
• If you have selected BS/SW BS as the 6ch AMP setting, “RB”
and “LB” are not appeared but “BS” is appeared on the Display.
2
Press the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to
select the “DISTANCE” on setup displays and press the
SETUP key again.
3
Use the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to
select the unit of distance.
1
METERS : meters
2
FEET : feet
4
Press the SETUP key to accept the setting.
5
Use the MULTI CONTROL
∞¥5
keys or TRIM
∞
/
5
keys to
adjust the distance to the front speakers.
The speaker indicator to be adjusted blinks.
• The allowable setting range is 0.3 to 9.0 m, adjustable in 0.3 m
increments.
6
Press the SETUP key to accept the setting.
7
Repeat steps
5
and
6
to input the distance for each of the
speakers.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
8
Press the SETUP key to exit the SETUP mode.
MUTE DOLBY DEX NEO:6 DSP TS DIGITAL ST.
AUTO
L
LFE SW
C R
DOLBY PL
II
DTS -ES AAC
DISCRETE
MATRIX 6.1
ACTIVE EQ.
LS S BS RS
名称未設定-8
04.3.25, 4:48 PM 16