Unit
X57-608X-XX
X53-3930-10
X45-3610-10
Model &
Frequency range
Remarks
Charger
Battery
Antenna
destination
0-10
0-11
0-10
0-10
TK-190
K
✔
✔
✔
29.7~37.0MHz
IF1: 128.55MHz
OP
OP
OP
K2
✔
✔
✔
35.0~50.0MHz
LOC: 129.005MHz
OP
OP
OP
FCC COMPLIANCE AND TYPE NUMBERS
Model
Type acceptance number
Frequency range
Compliance
TK-190 K
ALH29521110
29.7~37.0MHz
Parts 22,90
TK-190 K2
ALH29521120
35.0~50.0MHz
Part 90
2
TK-190
GENERAL / SYSTEM SET-UP
INTRODUCTION
SCOPE␣ OF␣ THIS␣ MANUAL
This manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade com-
munications equipment. It contains all required service in-
formation for the equipment and is current as of the publica-
tion date. Changes which may occur after publication are
covered by either Service Bulletins or Manual Revisions.
These are issued as required.
ORDERING␣ REPLACEMENT␣ PARTS
When ordering replacement parts or equipment informa-
tion, the full part identification number should be included.
This applies to all parts : components, kits, or chassis. If the
part number is not known, include the chassis or kit number
of which it is a part, and a sufficient description of the re-
quired component for proper identification.
PERSONNEL␣ SAFETY
The following precautions are recommended for person-
nel safety :
• DO␣ NOT␣ transmit until all RF␣ connectors are verified se-
cure and any open connectors are properly terminated.
• SHUT␣ OFF␣ and DO␣ NOT␣ operate this equipment near
electrical blasting caps or in an explosive atmosphere.
• This equipment should be serviced by a qualified techni-
cian only.
SERVICE
This radio is designed for easy servicing. Refer to the
schematic diagrams, printed circuit board views, and align-
ment procedures contained within.
Caution
Do not bring the antenna close to metallic objects.
65
TK-190
KSC-19
External View
KSC-19
Charging
KNB-17A
Voltage ................................................. 7.2V
Battery capacity ................................... 1500mAh
Charging time ....................................... Approx. 8 hours
KSC-20
External View
KSC-20
Specifications
Charging current ..................... 1100mA
±
150mA
Charging time ......................... KNB-17A : 80 min.
±
24%
Source voltage ........................ Approx 15V
Ambient temperature ............. 0
°
C~40
°
C
Dimensions ............................. 105 W x 135 D x 52 H (mm)
Weight .................................... 0.18kg
KPG-36
External View
KSC-19 (CHARGER) / KSC-20 (RAPID CHARGER) /
KPG-36 (PROGRAMMING INTERFACE CABLE)
KBP-4 External View
Battery case for 6x2 AA Alkaline Batteries
Merchandise received
License and frequency allocated by FCC
Choose the type of transceiver
Transceiver programming
Are you using the optional antenna?
Delivery
Are you using the speaker microphone?
TX/RX 29.7~37.0
6W/1W
TK-190 K
TX/RX 35.0~50.0
6W/1W
TK-190 K2
Frequency range (MHz)
RF power
Type
A personal computer (IBM PC or compatible), programming
interface (KPG-36), and programming software (KPG-59D)
are required for programming.
(The frequency, and signalling data are programmed for the
transceiver.)
YES
YES
NO
NO
KRA-21
Helical antenna
(Option)
KMC-25A
SYSTEM SET-UP
Note :
Internal beat interference exists at both 33. 600MHz and 42.000MHz.