Kenwood KNA-DV2600 Instruction Manual Download Page 71 | Manualshive

Page: 71 / 72

background image

English

|

71

Troubleshooting

■

Navigation System (KNA-DV2600)

?

The power does not come on.

✔

The fuse might be blown.

☞

Check the fuse. Replace it if it is blown.

?

The map does not scroll even when the vehicle is

moving.

✔

The screen shown might not be the Current Position
screen.

☞

See page 11 of this manual to display the Current

Position screen.

?

The vehicle marker does not appear.

✔

The screen shown might not be the Current Position
screen.

☞

See page 6 of this manual to display the Current

Position screen.

?

The GPS marker is not displayed.

✔

The GPS antenna or your vehicle might be in a position
where GPS signals cannot be received.

☞

Try moving the GPS antenna or your vehicle to a

position where there are no obstacles around.

?

The GPS marker is not displayed on the road where

your vehicle is running.

✔

TV channel 15 is now received.

☞

The GPS system may be affected by the channel-

15 signals as RF signals which are twice higher
than channel-15 signals are very close to the GPS
satellite receiving frequency. Try to tune a channel
other than channel 15.

?

There is no voice guidance.

✔

Route guidance might be suspended.

☞

The route guidance is off, see <Route Guidance>

(page 37).

✔

The guidance volume might be turned down low.

☞

See <Adjustment the volume of voice guidance>

(page 13).

?

Small spots or bright flashes appear in the screen

displayed.

✔

This is probably due to the nature of the LCD display.

☞

There is nothing wrong with the display and no

need for concern.

?

The map disc cannot be ejected.

✔

The disc might be incompatible or might have been
inserted incorrectly.

☞

Restart the engine and see page 4 of this manual.

■

AVN-2675's Monitor Unit

?

The power does not turn on.

✔

The fuse has blown.

☞

After checking for short circuits in the cables,

replace the fuse with one having the same rating.

✔

No ACC position on vehicle ignition.

☞

Connect the same cable to the ignition as the

battery cable.

?

No video picture appears.

✔

The unit is not connected to the parking brake
detection switch.

☞

Make proper connections according to

<Installationg Manual>.

✔

The parking brake is not engaged.

☞

For safety reasons no video picture are displayed

while the vehicle is moving. Engaging the parking
brake will cause picture to be displayed.

?

The screen is dark.

✔

The unit is in a location where temperature is low.

☞

If the temperature of the monitor unit drops, the

screen may appear darker when power is first
turned on due to the characteristics of a liquid
crystal panel. Wait a while after turning power on
for the temperature to rise. Normal brightness will
return.

Confirm whether any problem is due to a minor operational error or a malfunction. Check the table
below before contacting your local dealer for any repair service.

KNA-2600̲r3.0̲English.Indd 71

03.12.4, 10:32:23 PM

«
...
69
70
71
72
»

Summary of Contents for KNA-DV2600









































































Reviews:

No comments

Related manuals for KNA-DV2600

nuvi 800 series

Brand: Garmin Pages: 12

980915 - TrafficKit - NavTraffic Receiver

Brand: Magellan Pages: 86

Brand: Sound Storm Pages: 12

Brand: Hardstone Pages: 9

Brand: Macrom Pages: 5

Brand: Blaupunkt Pages: 16

Brand: Boss Audio Systems Pages: 22

Brand: Pioneer Pages: 48

Brand: Pioneer Pages: 166

Brand: Kenwood Pages: 34

Brand: Kenwood Pages: 58

Brand: Kenwood Pages: 34

Brand: Kenwood Pages: 38

Brand: Kenwood Pages: 60

Brand: Kenwood Pages: 21

Brand: Kenwood Pages: 40

Brand: Kenwood Pages: 46

Brand: Kenwood Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands